EEWORLDEEWORLDEEWORLD

Part Number

Search

LTC4252-2IMS8TRPBF

Description
Negative Voltage Hot Swap Controllers
File Size367KB,36 Pages
ManufacturerLinear ( ADI )
Websitehttp://www.analog.com/cn/index.html
Download Datasheet View All

LTC4252-2IMS8TRPBF Online Shopping

Suppliers Part Number Price MOQ In stock  
LTC4252-2IMS8TRPBF - - View Buy Now

LTC4252-2IMS8TRPBF Overview

Negative Voltage Hot Swap Controllers

LTC4252-1/LTC4252-2
LTC4252A-1/LTC4252A-2
Negative Voltage
Hot Swap Controllers
FEATURES
DESCRIPTIO
Allows Safe Board Insertion and Removal from a
Live – 48V Backplane
Floating Topology Permits Very High Voltage
Operation
Programmable Analog Current Limit With Circuit
Breaker Timer
Fast Response Time Limits Peak Fault Current
Programmable Soft-Start Current Limit
Programmable Timer with Drain Voltage
Accelerated Response
±1%
Undervoltage/Overvoltage Threshold Accuracy
(LTC4252A)
Adjustable Undervoltage/Overvoltage Protection
LTC4252-1/LTC4252A-1: Latch Off After Fault
LTC4252-2: Automatic Retry After Fault
Available in 8-Pin and 10-Pin MSOP Packages
The LTC
®
4252 negative voltage Hot Swap
TM
controller
allows a board to be safely inserted and removed from a
live backplane. Output current is controlled by three stages
of current limiting: a timed circuit breaker, active current
limiting and a fast feedforward path that limits peak
current under worst-case catastrophic fault conditions.
Adjustable undervoltage and overvoltage detectors dis-
connect the load whenever the input supply exceeds the
desired operating range. The LTC4252’s supply input is
shunt regulated, allowing safe operation with very high
supply voltages. A multifunction timer delays initial start-
up and controls the circuit breaker’s response time. The
circuit breaker’s response time is accelerated by sensing
excessive MOSFET drain voltage, keeping the MOSFET
within its safe operating area (SOA). An adjustable soft-
start circuit controls MOSFET inrush current at start-up.
The LTC4252-1/LTC4252A-1 latch off after a circuit breaker
fault times out. The LTC4252-2 provides automatic retry
after a fault. The LTC4252A-1/LTC4252A-2 feature tight
±1%
undervoltage/overvoltage threshold accuracy. The
LTC4252 is available in either an 8-pin or 10-pin MSOP.
, LT, LTC and LTM are registered trademarks of Linear Technology Corporation.
Hot Swap is a trademark of Linear Technology Corporation.
APPLICATIO S
Hot Board Insertion
Electronic Circuit Breaker
– 48V Distributed Power Systems
Negative Power Supply Control
Central Office Switching
High Availability Servers
ATCA
TYPICAL APPLICATIO
GND
– 48V/2.5A Hot Swap Controller
R
IN
3× 1.8k IN SERIES
1/4W EACH
C
IN
1µF
R1
402k
1%
V
IN
LTC4252-1
OV
UV
R2
32.4k
1%
C1
10nF
TIMER
C
T
0.33µF
SS
C
SS
68nF
V
EE
PWRGD
DRAIN
GATE
SENSE
R
C
10Ω
C
C
18nF
R
S
0.02Ω
PWRGD
10V/DIV
4252-1/2 TA01
+
C
L
100µF
LOAD
EN
GATE
5V/DIV
GND
(SHORT PIN)
R3
5.1k
*
R
D
1M
V
OUT
SENSE
2.5A/DIV
Q1
IRF530S
V
OUT
20V/DIV
–48V
* M0C207
U
Start-Up Behavior
1ms/DIV
4252-1/2 TA01a
U
U
425212fb
1
ARM assembly code analysis
As shown in the figure, this is an interrupt function handler that runs on M4. The corresponding C code function should be the following function, temp = h_0x10000158 & 0x3; switch(temp) { case 0,1,2,...
jplzl10000 ARM Technology
Accidentally leaked company source code to GitHub, fined 200,000 and sentenced to six months in prison!
[align=left][color=rgb(51, 51, 51)][font=微软雅黑][size=3]According to Southern Metropolis Daily, the Shenzhen Court recently made a first-instance judgment on the DJI source code leak case. Taking into a...
eric_wang Talking
It is recommended to open a lanuchpad section
The forum is now carrying out a lanuchpad learning activity, and everyone is very passionate.But I found that the TI section now has sections such as MCU, DSP, M3, etc., but there is no special sectio...
tiankai001 TI Technology Forum
Use of ad936x software
[i=s] This post was last edited by Buzhulun on 2015-3-15 21:01 [/i] I received a magazine from AD today. I think I wrote my information on the forum and received its brochure. Well, let's talk about A...
不足论 ADI Reference Circuit
Ready to use, STM32G474 driver for LIS2MDL magnetometer
The project is built using STM32CubeMX, STMems StandardC official driver, based on NUCLEO-G474 development board...
littleshrimp ST Sensors & Low Power Wireless Technology Forum
SparkRoad Evaluation (3) - Lookup Table and Combinatorial Logic Test
This board has the hardware for digital tube display. Next, I will conduct a simple test, a 3-input lookup table test, to verify the use of digital tubes and make a digital display module. module segt...
bigbat Domestic Chip Exchange

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2702  244  1691  1268  2704  55  5  35  26  4 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号