Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/
†
This product is only offered in trays. For more information go to:
http://www.linear.com/packaging/
available options
OUTPUT VOLTAGE
1.250
2.048
2.500
INITIAL ACCURACY
0.05%
0.1%
0.05%
0.1%
0.05%
0.1%
0.05%
0.1%
0.05%
0.1%
0.05%
0.1%
0.05%
0.1%
0.05%
0.1%
TEMPERATURE COEFFICIENT
5ppm/°C
10ppm/°C
5ppm/°C
10ppm/°C
5ppm/°C
10ppm/°C
5ppm/°C
8ppm/°C
5ppm/°C
10ppm/°C
5ppm/°C
10ppm/°C
5ppm/°C
10ppm/°C
5ppm/°C
10ppm/°C
PART NUMBER**
LTC6652AHMS8-1.25
LTC6652BHMS8-1.25
LTC6652AHMS8-2.048
LTC6652BHMS8-2.048
LTC6652AHMS8-2.5
LTC6652BHMS8-2.5
LTC6652AHLS8-2.5
LTC6652BHLS8-2.5
LTC6652AHMS8-3
LTC6652BHMS8-3
LTC6652AHMS8-3.3
LTC6652BHMS8-3.3
LTC6652AHMS8-4.096
LTC6652BHMS8-4.096
LTC6652AHMS8-5
LTC6652BHMS8-5
3.000
3.300
4.096
5.000
**See Order Information section for complete part number listing.
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C, V
IN
= V
OUT
+ 0.5V, unless otherwise noted.
PARAMETER
Output Voltage
Output Voltage Temperature Coefficient
(Note 3)
Line Regulation
Load Regulation (Note 4)
CONDITIONS
LTC6652A
LTC6652B
LTC6652A
LTC6652BMS8
LTC6652BLS8
V
OUT
+ 0.5V ≤ V
IN
≤ 13.2V,
SHDN
= V
IN
I
SOURCE
= 5mA, LTC6652-1.25, LTC6652-2.048,
LTC6652-2.5, LTC6652-3, LTC6652-3.3,
LTC6652-4.096, LTC6652-5
I
SINK
= 1mA, LTC6652-1.25, LTC6652-2.048
I
SINK
= 5mA, LTC6652-2.5, LTC6652-3,
LTC6652-3.3, LTC6652-4.096, LTC6652-5
l
l
l
electrical characteristics
MIN
–0.05
–0.1
TYP
MAX
0.05
0.1
UNITS
%
%
ppm/°C
ppm/°C
ppm/°C
ppm/V
ppm/V
ppm/mA
ppm/mA
ppm/mA
ppm/mA
ppm/mA
ppm/mA
6652fd
2
4
4
2
20
5
10
8
50
80
75
200
250
600
150
450
l
80
l
50
l
3
LTC6652
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C, V
IN
= V
OUT
+ 0.5V, unless otherwise noted.
PARAMETER
Minimum Operating Voltage (Note 5)
CONDITIONS
I
SOURCE
= 5mA, V
OUT
Error ≤ 0.1%
LTC6652-1.25, LTC6652-2.048
LTC6652-2.5, LTC6652-3, LTC6652-3.3,
LTC6652-4.096, LTC6652-5
Short V
OUT
to GND
Short V
OUT
to V
IN
Logic High Input Voltage
Logic High Input Current
Logic Low Input Voltage
Logic Low Input Current
Supply Current
Shutdown Current
Output Voltage Noise (Note 6)
No Load
l
l
l
l
l
l
l
electrical characteristics
MIN
2.7
V
OUT
+ 0.3V
TYP
MAX
UNITS
V
V
Output Short-Circuit Current
Shutdown Pin (SHDN)
16
16
2
0.1
0.1
350
l
mA
mA
1
0.8
1
560
2
V
µA
V
µA
µA
µA
µA
ppm
P-P
ppm
P-P
ppm
P-P
ppm
P-P
ppm
P-P
ppm
RMS
µs
ppm/√kHr
ppm/√kHr
ppm
ppm
SHDN
Tied to GND
0.1Hz ≤ f ≤ 10Hz
LTC6652-1.25
LTC6652-2.048, LTC6652-2.5, LTC6652-3
LTC6652-3.3
LTC6652-4.096
LTC6652-5
10Hz ≤ f ≤ 1kHz
0.1% Settling, C
LOAD
= 0
0.1
2.4
2.1
2.2
2.3
2.8
3
100
60
30
105
70
Turn-On Time
Long-Term Drift of Output Voltage (Note 7) LTC6652MS8
LTC6652LS8
Hysteresis (Note 8)
∆T = –40°C to 125°C, LTC6652MS8
∆T = –40°C to 125°C, LTC6652LS8
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
If the parts are stored outside of the specified temperature range,
the output may shift due to hysteresis.
Note 3:
Temperature coefficient is measured by dividing the maximum
change in output voltage by the specified temperature range.
Note 4:
Load regulation is measured on a pulse basis from no load to the
specified load current. Output changes due to die temperature change
must be taken into account separately.
Note 5:
Excludes load regulation errors.
Note 6:
Peak-to-peak noise is measured with a 3-pole highpass at 0.1Hz
and 4-pole lowpass filter at 10Hz. The unit is enclosed in a still-air
environment to eliminate thermocouple effects on the leads. The test
time is 10 seconds. RMS noise is measured on a spectrum analyzer in
a shielded environment where the intrinsic noise of the instrument is
removed to determine the actual noise of the device.
Note 7:
Long-term stability typically has a logarithmic characteristic and
therefore, changes after 1000 hours tend to be much smaller than before that
time. Total drift in the second thousand hours is normally less than one third
that of the first thousand hours with a continuing trend toward reduced drift
with time. Long-term stability will also be affected by differential stresses
between the IC and the board material created during board assembly.
Note 8:
Hysteresis in output voltage is created by package stress that differs
depending on whether the IC was previously at a higher or lower temperature.
Output voltage is always measured at 25°C, but the IC is cycled to the hot
or cold temperature limit before successive measurements. Hysteresis
is roughly proportional to the square of the temperature change. For
instruments that are stored at well controlled temperatures (within 20 or 30
degrees of operational temperature) it’s usually not a dominant error source.
Note 9:
The stated temperature is typical for soldering of the leads during
manual rework. For detailed IR reflow recommendations, refer to the
Applications section.
6652fd
4
LTC6652
Characteristic curves are similar for most
LTC6652s. Curves from the LTC6652-1.25, LTC6652-2.5 and the LTC6652-5 represent the extremes and typical of the voltage options.
Characteristic curves for other output voltages fall between these curves and can be estimated based on their output.
LabView practical skills video series : https://training.eeworld.com.cn/course/4337Lecture 1 - Creation of VI; Lecture 2 - Creation of polymorphic VI; Lecture 3 - Loop structure in program structure; ...
I couldn't enter for a while during the Chinese New Year, but I could enter two days ago. I went in to browse this morning, but now I can't enter. Is the community completely down?...
Nios II is a configurable 16-/32-bit RISC processor. Combined with a rich set of peripheral-specific instructions and hardware acceleration units, it provides a highly flexible and powerful SOPC sy...[Details]
The jammer is a signal blocker, mainly composed of a chip and a radio transmitter. When the car owner presses the remote control lock button, the jammer interferes with the electronic lock receivin...[Details]
Ever since the Tesla fire incident, electric cars, already known for their poor reputation, have been subjected to even more scathing criticism. Despite this, many people are still willing to buy t...[Details]
In the summer of 2025, BlueOval SK, a joint venture between Ford and SK On, officially started production at its first battery factory in Kentucky.
According to the original plan, this w...[Details]
On August 21st, Zhiyuan Robotics revealed at its first partner conference that it expects shipments to reach thousands of units this year and tens of thousands next year. The company hopes to reach...[Details]
introduction
Sonar imaging is of great significance in marine resource development and defense. Its long range, intuitive display of the observed area, and target identification make it widely...[Details]
The practice of warming up a car originated with gasoline-powered vehicles. Warming up the engine allows it to enter a better working state and ensures good lubrication. This has become a habit for...[Details]
1. Fault phenomenon and cause analysis
1. During the operation of the equipment, the expansion sleeve is subjected to a large torque, and the mating surfaces of the shaft and the sleeve move...[Details]
A tubular motor is an electric motor that is typically used to control the movement of machines and equipment. Tubular motors are generally divided into two categories: linear tubular motors and ro...[Details]
In the field of communications power supplies, AC/DC rectifier power supplies are called primary power supplies or basic power supplies, while DC/DC converters are called secondary power supplies. ...[Details]
A scale, a large, ground-mounted scale, is typically used to measure the tonnage of truck cargo. It's the primary weighing device used in factories, mines, and businesses for bulk cargo measurement...[Details]
01. Introduction
As in-vehicle networks migrate from the CAN
bus
to
Ethernet
, traditional millisecond-level synchronization accuracy can no longer meet the requirements of mul...[Details]
introduction
As core electronic components used in vastly different fields, automotive-grade chips and mobile/consumer-grade chips exhibit significant differences in their...[Details]
introduction
The OMAP-L138 dual-core processor is a new generation of low-power single-chip systems (SoCs) from TI. It is widely used in communications, industrial, medical diagnostic, and aud...[Details]
In microwave amplification circuits, the power chip is the core of the entire circuit. A large number of semiconductor devices in the chip will generate a lot of heat when working. If the heat diss...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
