or product names are trademarks or registered trademarks of their respective holders. The specifications and information herein are subject to change without notice.
www.latticesemi.com
1
gdx2fam_13
Lattice Semiconductor
Figure 1. ispGDX2 Block Diagram (256-I/O Device)
sysIO Bank
sysHSI
Block
ispGDX2 Family Data Sheet
sysIO Bank
SERDES
FIFO
GDX Block
SERDES
FIFO
sysHSI
Block
sysHSI
Block
sysCLOCK
PLL
SERDES
FIFO
SERDES
FIFO
GDX Block
sysCLOCK
PLL
sysHSI
Block
GDX Block
GDX Block
GDX Block
GDX Block
SERDES
SERDES
SERDES
SERDES
SERDES
sysHSI
Block
FIFO
FIFO
sysIO Bank
Introduction
The ispGDX2™ family is Lattice’s second generation in-system programmable generic digital crosspoint switch for
high speed bus switching and interface applications.
The ispGDX2 family is available in two options. The standard device supports sysHSI capability for ultra fast serial
communications while the lower-cost “E-series” supports the same high-performance FPGA fabric without the
sysHSI Block.
This family of switches combines a flexible switching architecture with advanced sysIO interfaces including high
performance sysHSI Blocks, and sysCLOCK PLLs to meet the needs of the today’s high-speed systems. Through
a muliplexer-intensive architecture, the ispGDX2 facilitates a variety of common switching functions.
The availability of on-chip control logic further enhances the power of these devices. A high-performance solution,
the family supports bandwidth up to 38Gbps.
Every device in the family has a number of PLLs to provide the system designer with the ability to generate multiple
clocks and manage clock skews in their systems.
sysIO Bank
sysIO Bank
GDX Block
GDX Block
SERDES
sysCLOCK
PLL
FIFO
FIFO
FIFO
FIFO
Global Routing Pool
(GRP)
sysHSI
Block
GDX Block
GDX Block
GDX Block
FIFO
SERDES
GDX Block
GDX Block
SERDES
SERDES
sysHSI
Block
FIFO
FIFO
sysIO Bank
GDX Block
GDX Block
GDX Block
FIFO
SERDES
FIFO
SERDES
FIFO
SERDES
sysHSI
Block
sysCLOCK
PLL
sysIO Bank
sysIO Bank
ISP & Boundary Scan
Test Port
2
Lattice Semiconductor
ispGDX2 Family Data Sheet
The sysIO interfaces provide system-level performance and integration. These I/Os support various modes of
LVCMOS/LVTTL and support popular high-speed standard interfaces such as GTL+, PCI-X, HSTL, SSTL, LVDS
and Bus-LVDS. The sysHSI Blocks further extend this capability by providing high speed serial data transfer capa-
bility.
Devices in the family can operate at 3.3V, 2.5V or 1.8V core voltages and can be programmed in-system via an
IEEE 1149.1 interface that is compliant with the IEEE 1532 standard. Voltages required for the I/O buffers are inde-
pendent of the core voltage supply. This further enhances the flexibility of this family in system designs.
Typical applications for the ispGDX2 include multi-port multi-processor interfaces, wide data and address bus mul-
tiplexing, programmable control signal routing and programmable bus interfaces. Table 1 shows the members of
the ispGDX2 family and their key features.
Architecture
The ispGDX2 devices consist of GDX Blocks interconnected by a Global Routing Pool (GRP). Signals interface
with the external system via sysIO banks. In addition, each GDX Block is associated with a FIFO and a sysHSI
Block to facilitate the transfer of data on- and off-chip. Figure 1 shows the ispGDX2 block diagram. Each GDX
Block can be individually configured in one of four modes:
• Basic (No FIFO or SERDES)
• FIFO Only
• SERDES Only
• SERDES and FIFO
Each sysIO bank has its own I/O power supply and reference voltage. Designers can use any output standard
within a bank that is compatible with the power supply. Any input standard may be used, providing it is compatible
with the reference voltage. The banks are independent.
Global Routing Pool (GRP)
The ispGDX2 architecture is organized into GDX Blocks, which are connected via a Global Routing Pool. The inno-
vative GRP is optimized for routability, flexibility and speed. All the signals enter via the GDX Block. The block sup-
plies these either directly or in registered form to the GRP. The GRP routes the signals to different blocks, and
provides separate data and control routing. The data path is optimized to achieve faster speed and routing flexibility
for nibble oriented signals. The control routing is optimized to provide high-speed bit oriented routing of control sig-
nals.
There are some restrictions on the allocation of pins for optimal bus routing. These restrictions are considered by
the software in the allocation of pins.
GDX Block
The blocks are organized in a “block” (nibble) manner, with each GDX Block providing data flow and control logic
for 16 I/O buffers. The data flow is organized as four nibbles, each nibble containing four Multiplexer Register
Blocks (MRBs). Data for the MRBs is provided from 64 lines from the GRP. Figure 2 illustrates the groups of signals
going into and out of a GDX Block.
Control signals for the MRBs are provided from the Control Array. The Control Array receives the 32 signals from
the GRP and generates 16 control signals: eight MUX Select, four Clock/Clock Enable, two Set/Reset and two Out-
put Enable. Each nibble is controlled via two MUX select signals. The remaining control signals go to all the MRBs.
Besides the control signals from the Control Array, the following global signals are available to the MRBs in each
GDX Block: four Clock/Clock Enable, one reset/preset, one power-on reset, two of four MUX select (two of two in
64 I/O), four Output Enable (two in 64 I/O) and Test Out Enable (TOE).
3
Lattice Semiconductor
MUX and Register Block (MRB)
ispGDX2 Family Data Sheet
Every MRB Block has a 4:1 MUX (I/O MUX) and a set of three registers which are connected to the I/O buffers,
FIFO and sysHSI Blocks. Multiple MRBs can be combined to form large multiplexers as described below. Figure 3
shows the structure of the MRB.
Each of the three registers in the MRB can be configured as edge-triggered D-type flip-flop or as a level sensitive
latch. One register operates on the input data, the other output data and the last register synchronizes the output
enable function. The input and output data signals can bypass each of their registers. The polarity of the data out
and output enable signals can be selected.
The Output and OE register share the same clock and clock enable signals. The Input register has a separate clock
and clock enable. The initialization signals of each register can be independently configured as Set or Reset. These
registers have programmable polarity control for Clock, Clock Enable and Set/Reset. The output enable register
input can be set either by one of the two output enables generated locally from the Control Array or from one of the
four (two in 64 I/O) Global OE enable pins. In addition to the local clock and clock enable signals, each MRB has
access to Global Clock, Clock Enable, Reset and TOE nets.
4
Lattice Semiconductor
Figure 2. GDX Block
GRP
32 bits
MUX
Control Select
8
8
ispGDX2 Family Data Sheet
GDX Block
sysIO Bank
Control Array
Nibble 0
OE
8
2
4 bits
MUX and Register
Block (MRB)
0
IN
OUT
8
2
OE
MUX and Register
Block (MRB)
1
IN
OUT
4 bits
8
2
4 bits
MUX and Register
Block (MRB)
2
OE
IN
OUT
8
OE
2
4 bits
MUX and Register
Block (MRB)
3
IN
OUT
8
2
16 bits
4
8
2
Nibble 1
MRBs 4-7
OE
IN
OUT
OE
IN
OUT
OE
IN
OUT
Nibble 2
MRBs 8-11
16 bits
4
8
2
16 bits
4
Nibble 3
MRBs 12-15
The output register of the MRB has a built-in bi-directional shift register capability. Each output register correspond-
ing to MRB “n”, receives data output from its two adjacent MRBs, MRB (n-1) and MRB (n+1), to provide shift regis-
ter capability. Like the output register, each input register of the MRB has built-in shift register capability. Each input
register can receive data from its two adjacent MRB input registers, to provide bi-directional shift register capability.
The chaining crosses GDX Block boundaries. The chain of input registers and the chain of output registers can be
After decompressing the wince image, are all the contents resident in the memory? To update the registry and database, it is necessary to read and write the flash, right? But when writing back to the ...
Actually, I have already written an application... But a senior said that the file system and SD card read and write implementation are too wasteful for 8962...
I would like to ask you a question, can...
Use MSP430 to drive 74HC595. Below is the main program. P2.0 is serial data input, P2.1 is RCK, and P2.2 is SCK. Assuming the serial input is 01010101, why can't I measure the voltage on the parallel ...
The ST3210E-LK development board is used for the test. The development environment is EWARM 5.0. There is no problem with the program started by the external crystal oscillator, but it cannot be used ...
Hello everyone, due to recent demand, I need to use a chip with adjustable voltage output from -150V to -300V, and a few milliamperes of current. It would be best if it is an automotive-grade chip. Wh...
There are many different ways of human-computer interaction. The more common ones are listed below:
Mouse interaction: Using a mouse to operate a computer and interact was the most common human...[Details]
In recent years, with the increasing demand for manufacturing and automated production management, industrial barcode scanners have gradually become an indispensable part of the industrial manufact...[Details]
The jammer is a signal blocker, mainly composed of a chip and a radio transmitter. When the car owner presses the remote control lock button, the jammer interferes with the electronic lock receivin...[Details]
On August 21, WeRide officially launched WePilot AiDrive, a one-stage end-to-end assisted driving solution developed in cooperation with Bosch. This comes only half a year after the two parties' "t...[Details]
Recently, South Korean robotics giant WIRobotics launched its first general-purpose humanoid robot, ALLEX, at the Robotics Innovation Center (RIH) at the Korea University of Science and Technology....[Details]
In the summer of 2025, BlueOval SK, a joint venture between Ford and SK On, officially started production at its first battery factory in Kentucky.
According to the original plan, this w...[Details]
As the scale and business applications of national e-government networks continue to expand, the data and services transmitted over them are becoming increasingly sensitive and critical. To protect...[Details]
There are basically three causes of spontaneous combustion of electric vehicles: The first is that the battery components are punctured or suffer fatal damage due to a collision accident, and part ...[Details]
Normally, we determine our location and where we want to go by comparing our surroundings with observation and simple GPS tools. However, this kind of reasoning is very difficult for self-driving c...[Details]
The practice of warming up a car originated with gasoline-powered vehicles. Warming up the engine allows it to enter a better working state and ensures good lubrication. This has become a habit for...[Details]
For today's new energy vehicles, they have different configurations from fuel vehicles, and some configurations have also become a selling point for manufacturers. Compared with traditional vehicle...[Details]
Definitions of VR
, AR, and MR:
What is Virtual Reality?
Virtual Reality (VR), also known as "spiritual realm" or "illusion," is a high-tech technology that has emerged in recent ye...[Details]
On August 19, according to foreign media Cyber Security News reported yesterday, a cybersecurity researcher discovered that hundreds of publicly accessible TeslaMate installation programs are leaki...[Details]
On August 18, Zhiyuan Robotics released information showing that the company's entire product line is officially on sale.
The full range of products launched this time includes six major produ...[Details]
Due to their small size and form factor, there are few existing printed circuit board standards for the growing wearable IoT market. Until these standards emerge, we must rely on knowledge gained f...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
