EEWORLDEEWORLDEEWORLD

Part Number

Search

8005PS2-660B

Description
Telecom and Datacom Connector, 12 Contact(s), Male, Right Angle, Solder Terminal, Locking, Receptacle
CategoryThe connector    The connector   
File Size35KB,1 Pages
ManufacturerSouth Sea Terminal Co., Ltd.
Download Datasheet Parametric View All

8005PS2-660B Overview

Telecom and Datacom Connector, 12 Contact(s), Male, Right Angle, Solder Terminal, Locking, Receptacle

8005PS2-660B Parametric

Parameter NameAttribute value
MakerSouth Sea Terminal Co., Ltd.
Reach Compliance Codeunknown
ECCN codeEAR99
Other featuresPIN SPACING=3.68MM BEFORE PEG
Board mount optionsSPLIT BOARD LOCK
body width0.535 inch
subject depth0.837 inch
body length1.225 inch
Body/casing typeRECEPTACLE
Connector typeTELECOM AND DATACOM CONNECTOR
Contact to complete cooperationAU ON NI
Contact point genderMALE
Contact styleTELCOM, MODULAR
insulator materialGLASS FILLED POLYESTER
Manufacturer's serial number8005PS
Installation option 1LOCKING
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of ports2
PCB contact patternSTAGGERED
Plating thickness3u inch
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.126 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts12
8005PS SERIES MODULAR JACK
Side Entry With Shield type
HOUSING : GLASS FILLED POLYESTER UL 94V-0
CONTACT : 0.46 MM DIAMETER ALLOY. GOLD PLATED OVER NICKET IN CONTACT AREA
GOLD PLATED : SELECTIVE GOLD PLATED.
170
Boot screen problem
I use the SDK provided by Sigma for embedded development. I want to display a boot screen when the board is powered on. I have an example here. However, after turning off the power, the image will be ...
cqk62 Embedded System
It's too troublesome to ask questions in this forum.
It's too troublesome to ask questions in this forum!!! When you raise a question, it takes a long time to review before it is published. Hey, can this be changed? Publish it first, then review it, and...
l0700830216 Suggestions & Announcements
The I2C master cannot generate a start bit
The I2C host program uses the official routine, but after executing the step of I2C_GenerateSTART(ENABLE), SB\MSL\BUSY is set, START is 0, and the SCL pin drops from 3.3V to about 100mv, while SDA is ...
Maxwell_CZH stm32/stm8
Why do OEMs like to specify Ethernet connectors?
Hello everyone! I recently received quotes from several OEMs, and two of them specified Ethernet connectors, but did not specify other connectors. I would like to ask the experts in vehicle architectu...
kong_jun77 Automotive Electronics
Have questions?
The following program compiles successfully, but during execution, I cannot get the expected result. Could you please help me take a look and give me some advice? Thank you!IMR .set 0004hIFR .set 0006...
blueeyeheyin Analogue and Mixed Signal
"Play Board" + Shared Bicycle Control Panel 1
I found a motherboard labeled as a shared bicycle control board on Xianyu. It was cheap, only 8 yuan, so I bought a few to play with. I haven't received the goods yet. I hope to learn some technologie...
chenzhufly Special Edition for Assessment Centres

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2282  765  1474  878  2097  46  16  30  18  43 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号