5962-9461002HZC datasheet, PDF

Datasheet> All Categories > storage> storage> 5962-9461002HZC

5962-9461002HZC: DescriptionFlash Module, 128KX32, 150ns, HIP-66; Categorystorage storage; File Size3MB，939 Pages; ManufacturerMicrosemi; Websitehttps://www.microsemi.com

Download Datasheet Parametric View All

5962-9461002HZC Overview

Flash Module, 128KX32, 150ns, HIP-66

5962-9461002HZC Parametric

Parameter Name	Attribute value
Maker	Microsemi
package instruction	HIP,
Reach Compliance Code	compliant
ECCN code	3A001.A.2.C
Maximum access time	150 ns
JESD-30 code	S-XHIP-P66
JESD-609 code	e4
length	30.1 mm
memory density	4194304 bit
Memory IC Type	FLASH MODULE
memory width	32
Number of functions	1
Number of terminals	66
word count	131072 words
character code	128000
Operating mode	ASYNCHRONOUS
Maximum operating temperature	125 °C
Minimum operating temperature	-55 °C
organize	128KX32
Package body material	UNSPECIFIED
encapsulated code	HIP
Package shape	SQUARE
Package form	IN-LINE
Parallel/Serial	PARALLEL
Programming voltage	5 V
Certification status	Not Qualified
Maximum seat height	5.84 mm
Maximum supply voltage (Vsup)	5.5 V
Minimum supply voltage (Vsup)	4.5 V
Nominal supply voltage (Vsup)	5 V
surface mount	NO
technology	CMOS
Temperature level	MILITARY
Terminal surface	GOLD
Terminal form	PIN/PEG
Terminal pitch	2.54 mm
Terminal location	HEX
type	NOR TYPE
width	30.1 mm
Base Number Matches	1

Preview

Download Datasheet

View All

NOT MEASUREMENT

SENSITIVE

MIL-HDBK-103AP

6 MARCH 2014

SUPERSEDING

MIL-HDBK-103AN

12 SEPTEMBER 2013

DEPARTMENT OF DEFENSE

HANDBOOK

LIST OF STANDARD MICROCIRCUIT DRAWINGS

This handbook is for guidance only. Do not cite this document

as a requirement.

AMSC N/A

FSC 5962

MIL-HDBK-103AP

CONTENTS

PARAGRAPH

1.1

1.2

1.2.1

1.2.2

1.2.3

1.2.4

4.1

4.2

4.3

4.4

4.5

4.6

5.1

5.2

6.1

6.1.1

6.1.2

6.2

7.1

7.2

TABLE 1

SECTION 1

Part I

Part II

Part III

PAGE

SCOPE .......................................................................................................................................... 1

Purpose...................................................................................................................................... 1

Part or identifying number (PIN) ................................................................................................ 1

Drawing number......................................................................................................................... 1

Device class designator ............................................................................................................. 1

Case outline / lead finish ............................................................................................................ 2

Substitutability ............................................................................................................................ 2

APPLICABLE DOCUMENTS ......................................................................................................... 2

DEFINITIONS ................................................................................................................................ 2

REQUIREMENTS .......................................................................................................................... 2

Drawing requirements ................................................................................................................ 2

Preparation procedures ............................................................................................................. 2

Drawing effectivity and duration ................................................................................................. 2

Approved sources of supply....................................................................................................... 2

Radiation hardness assurance (RHA) levels ............................................................................. 2

Electrostatic discharge sensitivity (ESD) listing ......................................................................... 3

CONFIGURATION MANAGEMENT .............................................................................................. 3

Configuration management of SMDs ......................................................................................... 3

Record of users.......................................................................................................................... 3

DISTRIBUTION and REQUESTS .................................................................................................. 4

Distribution ................................................................................................................................. 4

Automatic distribution ................................................................................................................ 4

Electronic distribution ................................................................................................................. 4

Requests .................................................................................................................................... 4

NOTES .......................................................................................................................................... 4

Intended use .............................................................................................................................. 4

Subject item (key word) listing ................................................................................................... 4

Noun code descriptions ................................................................................................................. 5

Microcircuits................................................................................................................................... 12

Listed by SMD PIN .....................................................................................................................

Listed by generic PIN .................................................................................................................

714

Listed approved sources ............................................................................................................

932

Concluding material ...................................................................................................................

936

iii

MIL-HDBK-103AP

1.2.3 Case outline/lead finish. Case outline and lead finish are as described in each SMD. The lead finish indicated in the

section 1 Part I listing is the most readily available from the manufacturer listed for the part. The manufacturer is authorized to

supply other lead finishes than what is listed provided that further testing/qualification is performed by the manufacturer on the

other lead finish(es). The user needs to contact the manufacturer to determine the availability of other lead finishes not listed

herein.

1.2.4 Substitutability. Device-class-Q devices will replace device-class-M devices.

2. APPLICABLE DOCUMENTS This section is not applicable to the handbook.

3. DEFINITIONS This section is not applicable to the handbook.

4. REQUIREMENTS

4.1 Drawing requirements. SMD's will be prepared in accordance with ASME Y14.100 and DOD directives.

4.2 Preparation procedures. The procedures for the generation of an SMD are provided in MIL-HDBK-780.

4.3 Drawing effectivity and duration. SMD's and device class M one part - one part number SMDs which have become

inactive for new design are reflected in section 1, part 1 of the appendix of this document with an "I" in the status column.

4.4 Approved sources of supply. The approved sources of supply list in this handbook supersedes the approved sources

formerly listed in each individual SMD/DLA Land and Maritime Drawing. This handbook is the official list of approved sources

of supply for non-one part - one part number SMD PIN's and for device class M one part - one part number SMD PIN's. Device

classes B, S, Q, V, T, N (monolithic) and H, K, D, G, E (hybrid) one part - one part number SMD PIN's are listed for the

convenience of the users. Official listing for B, S, Q, V, T, N, H, K, D, G, and E levels are available in the applicable QML.

Manufacturers should notify DLA Land and Maritime-VA in writing if they no longer wish to be listed as an approved source of

supply for any device listed herein. This letter will be used by DSCC to remove the manufacturer from MIL-HDBK-103 for

those devices that the manufacturer specifies that he will no longer supply.

4.5 Radiation hardness assurance (RHA) levels. SMD devices which meet the RHA requirements of MIL-PRF-38535 or

MIL-PRF-38534 will be marked with the appropriate RHA designator M, D, P, L, R, F, G, or H replacing the dash (-) in the PIN

as indicated in the following example:

5962(M, D, P, L, R, F, G, or H)8999901EA

Only the highest RHA level for which the device is qualified will be listed in Section 1, Part I of the appendix of this document;

however, at the request of the customer, the manufacturer is authorized to supply any lower RHA level device. At the request

of the customer, the non-RHA PIN designated with a dash (-) may be supplied at the option of the manufacturer. The

manufacturer may also opt to submit a certificate of compliance to have the non-RHA PIN listed in addition to the RHA PIN in

Section 1, Part I of the appendix of this document.

Recommended Resources

Mobile phone emergency charger circuit diagram produced by LM3578

TTL to CMOS interface circuit

Overheating protection circuit for power transistors

Integrated detection circuit

fast schmitt trigger

Single-ended switching power supply

SFR is a set of real physical registers, not part of RAM. It's just that their addresses overlap with part of RAM?: SFR is a set of real physical registers, not part of RAM. It's just that their addresses overlap with part of RAM?...; 吴通凯 Embedded System

I am an undergraduate student who is about to graduate, and I would like to ask for guidance!: I am quite confused now. I will graduate soon and will look for a job in September this year. I want to work in embedded hardware. I have the following feelings before looking for a job: 1. Software d...; liutogo Talking about work

Problems with opening STM8 projects with IAR: I use IAR to open the STM8 project, but it prompts abnormality.May I ask the experts if there is any problem? Thank you!...; chenbingjy stm32/stm8

How to put multiple files into a specified directory during cold start of wince?: How to add multiple (for example, 300) files to the specified directory of Windows in wince? ? If using .dat file to implement Directory("\windows\Programs"):-File("Test_HSPI.exe", "\Windows\Test_HSPI...; sqr7777777 Embedded System

Can anyone tell me the size of the TMP006 I bought in the group? The one with BGA package: [i=s] This post was last edited by dontium on 2015-1-23 13:11 [/i] I only saw from the manual that the spacing between the two BGA pads is 0.5MM. The pad size I used is 11mil but now I don’t know the ...; jcrorxp Analogue and Mixed Signal

The company has launched a new medical product, but is still hesitant about the piracy in the market. Is there any good way to promote it?: The company has launched a new medical product, but is still hesitant about the piracy in the market. Is there any good method you can recommend?...; UP798 Embedded System

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components