EEWORLDEEWORLDEEWORLD

Part Number

Search

WBA-T0303GC-07-5230-FG

Description
RES NET,THIN FILM,523 OHMS,100WV,1% +/-TOL,-25,25PPM TC,0303 CASE
CategoryPassive components    The resistor   
File Size484KB,3 Pages
ManufacturerTT Electronics plc
Websitehttp://www.ttelectronics.com/
Download Datasheet Parametric View All

WBA-T0303GC-07-5230-FG Overview

RES NET,THIN FILM,523 OHMS,100WV,1% +/-TOL,-25,25PPM TC,0303 CASE

WBA-T0303GC-07-5230-FG Parametric

Parameter NameAttribute value
MakerTT Electronics plc
Reach Compliance Codecompliant
ECCN codeEAR99
structureChip
Manufacturer's serial numberWBA
Network TypeCenter Tap
Number of terminals6
Maximum operating temperature150 °C
Minimum operating temperature-55 °C
Package length0.762 mm
Package formSMT
Package width0.762 mm
method of packingTray
Rated power dissipation(P)0.25 W
GuidelineMIL-PRF-38534
resistance523 Ω
Resistor typeARRAY/NETWORK RESISTOR
seriesWBA
size code0303
Temperature Coefficient-25,25 ppm/°C
Tolerance1%
Operating Voltage100 V
Wire Bondable
Ceramic Resistors
WBA Series
High resistor density
Lower stray capacitance
Proven TaNFilm
®
on ceramic technology
IRC’s WBA series wire bondable ceramic resistors are ideally suited for
your most demanding hybrid application. IRC’s TaNFilm
®
tantalum nitride
thin film technology has years of proven stability, reliability and moisture performance.
IRC’s WBA series of ceramic chip resistors offer a wide range of tolerances and temperature coefficients to fit
a variety of hybrid circuit applications. Custom resistance values, sizes and schematics are also available on
request to the factory.
For high performance wire bondable ceramic resistors for hybrid circuit application, specify IRC WBA series
resistors.
Electrical Data
Absolute Tolerance
Ratio Tolerance
Absolute TCR
Tracking TCR
Package Power Rating (@ 70°C)
Rated Operating Voltage
(not to exceed
P x R )
Operating Temperature
Noise
Substrate Material
Substrate Thickness
Bond Pad Metallization
Backside
to ±0.1%
to ±0.05%
to ±25ppm/°C
to ±2ppm/°C
250mW
100V
-55°C to +150°C
<-30dB
99.6% Alumina
0.015˝ ±0.002
(0.381mm ±0.05)
Gold: 30KÅ minimum
Ceramic (gold available)
Physical Data
T0303 - Tapped network
(0.762mm ±0.025)
0.004˝ min
Bond Pads
A subsidiary of
TT electronics plc
0.030˝ ±0.001
(0.762mm ±0.025)
½R
½R
General Note
IRC reserves the right to make changes in product specification without notice or liability.
All information is subject to IRC’s own data and is considered accurate at time of going to print.
© IRC Advanced Film Division
• 4222 South Staples Street • Corpus Christi Texas 78411 USA
Telephone: 361 992 7900 • Facsimile: 361 992 3377 • Website: www.irctt.com
WBA Series Issue January 2009 Sheet 1 of 3
0.030˝ ±0.001
How to use PB5 to develop CE device drivers?
I want to learn about CE driver development recently. I bought a book that talks a lot about native drivers and stream drivers, but it doesn't show how to make a driver specifically. It just gives som...
xiaozhou Embedded System
Submit your evaluation proposal and be the first to experience the Cyclone V evaluation board!
[align=left][size=3][color=#000000] In order to let more friends know about and participate in this Cyclone V trial event, and also hope to maximize the value of Cyclone V. We will extend the applicat...
EEWORLD社区 FPGA/CPLD
How should I calculate the I2C delay?
Dear seniors who have used I2C analog communication, I have just learned this and there are some places I don't understand. I hope you can give me some advice: I use the tea5990 radio chip with an I2C...
saioooooo Embedded System
ESD resistance of capacitors
This article explains the ESD (Electrostatic Discharge) resistance of capacitors. ESD resistance test method When static electricity carried by the human body and equipment is discharged to the entire...
fish001 Analogue and Mixed Signal
[TI's first low-power design competition] Asking for advice on TTP229 touch panel circuit
[i=s]This post was last edited by lonerzf on 2014-9-27 09:04[/i] I recently saw a capacitive touch switch circuit made with TTP229. I plan to apply it to MSP430FR5969, but I don't know what to pay att...
lonerzf Microcontroller MCU
GetDC and then ReleaseDC(), memory leak occurs
After drawing with memory, I have RealseDC for memDC and pDC. But in the end, there is still insufficient memory. After one minute of looping, it prompts insufficient memory and memory leak. http://su...
zhengyusun Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1034  683  2027  2350  2448  21  14  41  48  50 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号