• SerDes associated with unused ports are turned-off
• SerDes associated with unused lanes are placed in a low
power state
54 General Purpose I/O
Reliability, Availability and Serviceability (RAS)
ECRC support
AER on all ports
SECDED ECC protection on all internal RAMs
End-to-end data path parity protection
Checksum Serial EEPROM content protected
Autonomous link reliability (preserves system operation in the
presence of faulty links)
–
Ability to generate an interrupt (INTx or MSI) on link up/down
transitions
Test and Debug
–
On-chip link activity and status outputs available for several
ports including the upstream ports
–
Per port link activity and status outputs available using
external I
2
C I/O expander for all remaining ports
–
SerDes test modes
–
Supports IEEE 1149.6 AC JTAG and IEEE 1149.1 JTAG
–
–
–
–
–
–
Power Supplies
–
Requires only two power supply voltages (1.0 V and 2.5 V)
Note that a 3.3V is preferred for V
DD
I/O
–
No power sequencing requirements
Packaged in a 35mm x 35mm 1156-ball Flip Chip BGA with
1mm ball spacing
Product Description
Utilizing standard PCI Express interconnect, the PES48H12AG2
provides the most efficient fan-out solution for applications requiring
high throughput, low latency, and simple board layout with a minimum
number of board layers. It provides 48 GBps (384 Gbps) of aggregated,
full-duplex switching capacity through 48 integrated serial lanes, using
proven and robust IDT technology. Each lane provides 5 GT/s of band-
width in both directions and is fully compliant with PCI Express Base
Specification, Revision 2.0.
The PES48H12AG2 is based on a flexible and efficient layered
architecture. The PCI Express layer consists of SerDes, Physical, Data
Link and Transaction layers in compliance with PCI Express Base spec-
ification Revision 2.0. The PES48H12AG2 can operate either as a store
and forward or cut-through switch. It supports eight Traffic Classes
(TCs) and one Virtual Channel (VC) with sophisticated resource
management to enable efficient switching and I/O connectivity for
servers, storage, and embedded processors with limited connectivity.
The PES48H12AG2 is a
partitionable
PCIe switch. This means that
in addition to operating as a standard PCI express switch, the
PES48H12AG2 ports may be partitioned into groups that logically
operate as completely independent PCIe switches.
Figure 2
illustrates a
three partition PES48H12AG2 configuration.
2 of 59
December 12, 2013
IDT 89HPES48H12AG2 Datasheet
Block Diagram
x8/x4/x2/x1
x8/x4/x2/x1
x8/x4/x2/x1
SerDes
DL/Transaction Layer
SerDes
DL/Transaction Layer
SerDes
DL/Transaction Layer
Route Table
Port
Arbitration
12-Port Switch Core
Frame Buffer
Scheduler
DL/Transaction Layer
DL/Transaction Layer
DL/Transaction Layer
SerDes
SerDes
SerDes
x8/x4/x2/x1
x8/x4/x2/x1
x8/x4/x2/x1
48 PCI Express Lanes
Up to 6 x8 ports or 12 x4 Ports
Figure 1 Internal Block Diagram
Partition 1
Upstream Port
Partition 2
Upstream Port
Partition 3
Upstream Port
P2P
Bridge
P2P
Bridge
P2P
Bridge
Partition 1 – Virtual PCI Bus
Partition 2 – Virtual PCI Bus
Partition 3 – Virtual PCI Bus
P2P
Bridge
P2P
Bridge
P2P
Bridge
P2P
Bridge
P2P
Bridge
P2P
Bridge
P2P
Bridge
P2P
Bridge
Partition 1
Downstream Ports
Partition 2
Downstream Ports
Partition 3
Downstream Ports
Figure 2 Example of Usage of Switch Partitioning
SMBus Interface
The PES48H12AG2 contains two SMBus interfaces. The slave interface provides full access to the configuration registers in the PES48H12AG2,
allowing every configuration register in the device to be read or written by an external agent. The master interface allows the default configuration
register values of the PES48H12AG2 to be overridden following a reset with values programmed in an external serial EEPROM. The master interface
is also used by an external Hot-Plug I/O expander.
3 of 59
December 12, 2013
IDT 89HPES48H12AG2 Datasheet
Six pins make up each of the two SMBus interfaces. These pins consist of an SMBus clock pin, an SMBus data pin, and 4 SMBus address pins. In
the slave interface, these address pins allow the SMBus address to which the device responds to be configured. In the master interface, these
address pins allow the SMBus address of the serial configuration EEPROM from which data is loaded to be configured. The SMBus address is set up
on negation of PERSTN by sampling the corresponding address pins. When the pins are sampled, the resulting address is assigned as shown in
Table 1.
Bit
1
2
3
4
5
6
7
Slave
SMBus
Address
SSMBADDR[1]
SSMBADDR[2]
SSMBADDR[3]
0
SSMBADDR[5]
1
1
Master
SMBus
Address
MSMBADDR[1]
MSMBADDR[2]
MSMBADDR[3]
MSMBADDR[4]
1
0
1
Table 1 Master and Slave SMBus Address Assignment
As shown in
Figure 3,
the master and slave SMBuses may only be used in a split configuration.
Switch
Processor
SMBus
Master
...
Other
SMBus
Devices
SSMBCLK
SSMBDAT
MSMBCLK
MSMBDAT
Serial
EEPROM
Hot-Plug
I/O
Expander
Figure 3 Split SMBus Interface Configuration
The switch’s SMBus master interface does not support SMBus arbitration. As a result, the switch’s SMBus master must be the only master in the
SMBus lines that connect to the serial EEPROM and I/O expander slaves. In the split configuration, the master and slave SMBuses operate as two
independent buses; thus, multi-master arbitration is not required.
Hot-Plug Interface
The PES48H12AG2 supports PCI Express Hot-Plug on each downstream port. To reduce the number of pins required on the device, the
PES48H12AG2 utilizes an external I/O expander, such as that used on PC motherboards, connected to the SMBus master interface. Following reset
and configuration, whenever the state of a Hot-Plug output needs to be modified, the PES48H12AG2 generates an SMBus transaction to the I/O
expander with the new value of all of the outputs. Whenever a Hot-Plug input changes, the I/O expander generates an interrupt which is received on
the IOEXPINTN input pin (alternate function of GPIO) of the PES48H12AG2. In response to an I/O expander interrupt, the PES48H12AG2 generates
an SMBus transaction to read the state of all of the Hot-Plug inputs from the I/O expander.
4 of 59
December 12, 2013
IDT 89HPES48H12AG2 Datasheet
General Purpose Input/Output
The PES48H12AG2 provides 54 General Purpose Input/Output (GPIO) pins that may be used by the system designer as bit I/O ports. Each GPIO
pin may be configured independently as an input or output through software control. Some GPIO pins are shared with other on-chip functions. These
alternate functions may be enabled via software, SMBus slave interface, or serial configuration EEPROM.
Pin Description
The following tables list the functions of the pins provided on the PES48H12AG2. Some of the functions listed may be multiplexed onto the same
pin. The active polarity of a signal is defined using a suffix. Signals ending with an “N” are defined as being active, or asserted, when at a logic zero
(low) level. All other signals (including clocks, buses, and select lines) will be interpreted as being active, or asserted, when at a logic one (high) level.
Signal
PE00RP[3:0]
PE00RN[3:0]
PE00TP[3:0]
PE00TN[3:0]
PE01RP[3:0]
PE01RN[3:0]
PE01TP[3:0]
PE01TN[3:0]
PE02RP[3:0]
PE02RN[3:0]
PE02TP[3:0]
PE02TN[3:0]
PE03RP[3:0]
PE03RN[3:0]
PE03TP[3:0]
PE03TN[3:0]
PE04RP[3:0]
PE04RN[3:0]
PE04TP[3:0]
PE04TN[3:0]
PE05RP[3:0]
PE05RN[3:0]
PE05TP[3:0]
PE05TN[3:0]
PE06RP[3:0]
PE06RN[3:0]
PE06TP[3:0]
PE06TN[3:0]
Type
I
O
I
Name/Description
PCI Express Port 0 Serial Data Receive.
Differential PCI Express receive
pairs for port 0.
PCI Express Port 0 Serial Data Transmit.
Differential PCI Express trans-
mit pairs for port 0.
PCI Express Port 1 Serial Data Receive.
Differential PCI Express receive
pairs for port 1. When port 0 is merged with port 1, these signals become
port 0 receive pairs for lanes 4 through 7.
PCI Express Port 1 Serial Data Transmit.
Differential PCI Express trans-
mit pairs for port 1. When port 0 is merged with port 1, these signals
become port 0 transmit pairs for lanes 4 through 7.
PCI Express Port 2 Serial Data Receive.
Differential PCI Express receive
pairs for port 2.
PCI Express Port 2 Serial Data Transmit.
Differential PCI Express trans-
mit pairs for port 2.
PCI Express Port 3 Serial Data Receive.
Differential PCI Express receive
pairs for port 3. When port 2 is merged with port 3, these signals become
port 2 receive pairs for lanes 4 through 7.
PCI Express Port 3 Serial Data Transmit.
Differential PCI Express trans-
mit pairs for port 3. When port 2 is merged with port 3, these signals
become port 2 transmit pairs for lanes 4 through 7.
PCI Express Port 4 Serial Data Receive.
Differential PCI Express receive
pairs for port 4.
PCI Express Port 4 Serial Data Transmit.
Differential PCI Express trans-
mit pairs for port 4.
PCI Express Port 5 Serial Data Receive.
Differential PCI Express receive
pairs for port 5. When port 4 is merged with port 5, these signals become
port 4 receive pairs for lanes 4 through 7.
PCI Express Port 5 Serial Data Transmit.
Differential PCI Express trans-
mit pairs for port 5. When port 4 is merged with port 5, these signals
become port 4 transmit pairs for lanes 4 through 7.
[color=#666666][font=Arial, Helvetica, sans-serif][size=18px]Every April Fools’ Day, there are all kinds of deceptive dynamics in the circle of friends. As expected, I saw quite a few today. Let’s tal...
Experts, when using labs_2b to identify motor parameters, if the motor has a Hall sensor, do I need to connect the Hall sensor to the driver board? The driver board I have does not have a Hall sensor ...
"There's nothing I can't do, except what you can't think of!""The earthworm motor can handle all these terrains, including mountains, vegetable fields, dry land, wetlands, hills, plains, and river ban...
Friendly reminder: Thanks to the kindness of netizens, I saw that some netizens reposted this post, thank you! I hope everyone will indicate the author when reposting: Jiaozuo Huarun Bai Zhigang. At p...
[font=Courier]At the beginning of 2008, the automotive electronics industry reviewed the development of 2007 and raised some thought-provoking questions. Local automotive electronics companies will fa...
[i=s]This post was last edited by paulhyde on 2014-9-15 09:08[/i] I looked at the component list for 2003 and there was a high-frequency varactor diode, and the topic for that year was a voltage-contr...
The problem of dynamic sealing of equipment always exists with the operation of the equipment. Today, we have specially sorted out the various commonly used sealing forms, usage scope and character...[Details]
On August 22, Lantu Motors officially launched its Lanhai Intelligent Hybrid technology via an online livestream. This intelligent hybrid technology, which integrates a full-range 800V high-voltage...[Details]
introduction
According to the China Fire Statistics Yearbook, electrical fires accounted for more than 30% of fire accidents in the past decade, and the trend is increasing year by year. They ...[Details]
As AI accelerates across industries, the demand for data center infrastructure is also growing rapidly.
Keysight Technologies, in collaboration with Heavy Reading, released the "Beyo...[Details]
The difference between a series inverter and a parallel inverter is that they use different oscillation circuits. A series inverter connects L, R, and C in series, while a parallel inverter connect...[Details]
Shenzhen Baowei Power Supply high frequency pure sine wave power, communication inverter power supply has two communication interfaces, RS232 and R485 interfaces, their functions and characteristic...[Details]
Previously, Positive Motion Technology shared with you the firmware upgrade of motion controller, ZBasic program development, ZPLC program development, communication with touch screen and input/out...[Details]
Common methods for troubleshooting roller press bearing wear include repair welding, thermal spraying, brush plating, and scrapping and replacement. However, these methods are often subject to asse...[Details]
Civilian internal combustion engines operate in the range of approximately 1000-4000 rpm. This results in the engine's kinetic energy being ineffective at low or high rpm, making starting difficult...[Details]
Renesas Electronics' new ultra-low-power RA4C1 MCU features advanced security and a dedicated peripheral set, making it ideal for metering and other applications.
The new product mee...[Details]
introduction
In recent years, multi-touch has emerged as a new alternative to traditional human-computer interaction. It eliminates the need for keyboards and mice, enabling simultaneous inter...[Details]
Smartphones can be incredibly unintelligent. For example, consider an office full of people, each absorbed in their work. Suddenly, the silence is broken by a burst of loud pop music. A colleague's...[Details]
The Waveshare ESP32-P4-ETH is a compact ESP32-P4 development board with Ethernet and PoE support. It looks very similar to the Olimex ESP32-P4-DevKit, minus the pUEXT connector. However, we've also...[Details]
In industrial production, many different controllers are often used, such as those for pressure, flow, electrical parameters, temperature, and sound. However, due to the limitations of the on-site ...[Details]
Talking
京公网安备 11010802033920号
EEWORLD
