EEWORLDEEWORLDEEWORLD

Part Number

Search

3EQHM572-B-20.000N-D2.7

Description
CMOS Output Clock Oscillator, ROHS COMPLIANT, MINIATURE, SMD, 4 PIN
CategoryPassive components    oscillator   
File Size270KB,3 Pages
ManufacturerEuroquartz
Websitehttp://www.euroquartz.co.uk/
Environmental Compliance
Download Datasheet Parametric View All

3EQHM572-B-20.000N-D2.7 Overview

CMOS Output Clock Oscillator, ROHS COMPLIANT, MINIATURE, SMD, 4 PIN

3EQHM572-B-20.000N-D2.7 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerEuroquartz
Reach Compliance Codecompliant
JESD-609 codee4
Oscillator typeCMOS
Terminal surfaceGold (Au) - with Nickel (Ni) barrier
EURO
QUARTZ
Provides from 8dB to 15dB reduction in system EMI
‘Drop-in’ replacement for standard clocks
Choice of modulation rate and spread
Miniature package: 7.0 mm x 5.0 mm x 1.4mm
N Group parts provide a low cost EMI reduction solution
3EQHM572N Low EMI Oscillator
Page 1 of 3
7 x 5 x 1.4mm SMD - Group 'N'
In electrical systems the principal cause of electro-
magnetic interference (EMI) is the system clock
oscillator. Traditional methods of 'patching-up' systems
with too high a level of EMI is to use ferrite beads,
filters, ground planes, metal shielding and similar costly
methods, However, the most efficient and economic
method to reduce EMI is to reduce it at source: replace
the system clock ocillator with a low EMI clock oscillator.
Compared with conventional clock oscillators, Spread
Spectrum (Dithered) Oscillators can reduce EMI by as
much as 16dB. The part is a 'drop-in' replacement for a
standard clock oscillator hence there is no requirement
to re-design existing PCBs.
DESCRIPTION
EQHM572 series low EMI oscillators can reduce system EMI from 8dB
to 16dB. The oscillators are a ‘drop-in’ replacement for standard
oscillators. EMI reduction is achieved by the use of Spread Spectrum
Technology whereby the mode energy is spread over a wider
bandwidth. The modulation carrier frequency, operating in the kHz
region, makes the process transparent to the oscillator frequency.
There is a choice of modulation rates and spread to suit application
requirements.
SPREAD SPECTRUM TECHNOLOGY
Unlike a conventional clock oscillator, in a Spread Spectrum Clock
Oscillator the mode energy is spread over a wider bandwidth. This is
achieved by the frequency modulation technique. The controlled
modulation process may be applied to the 'down' side of the nominal
frequency (known as
DOWN SPREAD,)
or spread equally either side
of nominal (CENTRE
SPREAD).
Down Spread is preferred if over-
clocking would cause a problem to the system.
APPLICATIONS
Printers, Multiple Function Printers (MPCs)
Digital Copiers; PDAs
Networking: LAN/WAN; Routers
Storage Systems (CD-ROM, VCD, DVD, HDD)
Scanners; Modems; Projectors
Embedded Systems
Musical Instruments
Automotive: GPS car navigation systems
LCD PC Monitors; LSD TVs
ADSL; PCMCIA
Still Digital Cameras (SDCs)
Medical devices
MODULATION TYPES - EXAMPLES
EUROQUARTZ LIMITED Blacknell Lane CREWKERNE Somerset UK TA18 7HE
Tel: +44 (0)1460 230000 Fax: +44 (0)1460 230001 info@euroquartz.co.uk www.euroquartz.co.uk
It is recommended that EMI/EMC information and discussion issues be sent here
EMI/EMC is a difficult problem for most PCB designs. I hope you can post relevant EMI/EMC information and discussion in one post to help everyone search and discuss! ~...
天道自然 PCB Design
Application of Active and Passive Safety Technology in Automobiles in the New Century
1. Active safety system Active safety system refers to a safety system that prevents accidents by taking precautions in advance. It is expected to reduce casualties in traffic accidents in the most th...
frozenviolet Automotive Electronics
DSP2812
Can DSPF2812 control two modules that need serial port control with one serial port? A voice module and an LCD module. Both of them need serial port to send commands and receive the same content!...
羽翼之杨勇0102 DSP and ARM Processors
Voltage change detection and analysis
How should I analyze this circuit diagram, [img=110,0]https://bbs.eeworld.com.cn/ajaximage.php?aid=93546&size=300x300&key=82d8e62ef9272a74cd176c3374945057&nocache=yes&type=fixnone[/img]? How did I bui...
xkc6659 Analog electronics
Design of passive switch signal trigger relay? ?
Hello friends: I have a Bosch infrared passive detector. When the alarm is triggered, it outputs a disconnected switch signal. I want to use this signal to control the speaker to send out an alarm sig...
zhaofan0505 Embedded System
Square wave rise time measurement
The square wave signal has a low voltage of 0V, an amplitude of 3.3V, and a frequency of 1Hz to 2MHz. How to use analog circuits plus FPGA to measure the rise time of the square wave's rising edge?...
燕园技术宅 Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1549  156  1174  2367  2752  32  4  24  48  56 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号