EEWORLDEEWORLDEEWORLD

Part Number

Search

8168S2H9V2BE2

Description
Pushbutton Switch, SPDT, On-(on), Vertical, 7 PCB Hole Cnt, Solder Terminal, Through Hole-right Angle
CategoryMechanical and electronic products    switch   
File Size571KB,10 Pages
ManufacturerITT
Websitehttp://www.ittcannon.com/
Download Datasheet Parametric View All

8168S2H9V2BE2 Overview

Pushbutton Switch, SPDT, On-(on), Vertical, 7 PCB Hole Cnt, Solder Terminal, Through Hole-right Angle

8168S2H9V2BE2 Parametric

Parameter NameAttribute value
MakerITT
Reach Compliance Codeunknown
ECCN codeEAR99
Actuator angle
Actuator colorBLACK
Executor completedGLOSS
Actuator length0.41 inch
Actuator materialNYLON
Actuator typePUSHBUTTON
body width9.144 mm
body height36.83 mm
Body length or diameter19.05 mm
Casing diameter0.25 inch
Nozzle length0.3 inch
Casing typeUNTHREADED
Center contact platingGOLD OVER NICKEL
Contact (DC) maximum rated power R load0.4VA@20VDC
Contact functionON-(ON)
Contact resistance0.02 mΩ
Dielectric withstand voltage1000VAC V
Electrical life50000 Cycle(s)
End contact materialCOPPER ALLOY
End contact platingGOLD OVER NICKEL
Shell materialSTAINLESS STEEL
Insulation resistance1000000000 Ω
insulator materialGLASS FILLED NYLON
Manufacturer's serial number8060
Installation featuresTHROUGH HOLE-RIGHT ANGLE
Maximum operating temperature65 °C
Minimum operating temperature-30 °C
PCB hole count7
sealEPOXY
SolderabilityMIL-STD
surface mountNO
Switch actionVERTICAL
switch functionSPDT
Switch typePUSHBUTTON SWITCH
Terminal surfaceGOLD/NICKEL
Terminal length0.185 inch
Terminal materialCOPPER ALLOY
Termination typeSOLDER
WashabilityPARTIAL
Printed from www.freetradezone.com, a service of Partminer, Inc.
This Material Copyrighted By Its Respective Manufacturer
Chengdu University of Technology Microcontroller Courseware
Chengdu University of Technology Microcontroller Courseware...
wangwei20060608 MCU
How to identify the three poles of thyristor
The method to identify the three poles of thyristor is very simple. According to the principle of PN junction, you only need to use a multimeter to measure the resistance between the three poles.The f...
fighting Analog electronics
Please tell me about the connection status and disconnection of RAS!!
I would like to ask all the heroes!! I can now use RAS to dial up the Internet. I would like to ask how to know whether the dial-up is successful? Which function is called? There is another question!!...
yynan Embedded System
DIY cheap CPLD learning board
This is a CPLD learning board I DIYThe purpose of DIY is to learn and understand the development process of CPLD, so the function is relatively simple, with only a few LEDs, hahaSince it is all handma...
chenzhufly DIY/Open Source Hardware
About the AD sampling fluctuation of DSP
When the voltage waveform at the AD port of DSP is a pure sine wave (as shown in the red waveform), the AD sampling result will have non-periodic bad pixels (as shown in the blue waveform). The figure...
zk_123 DSP and ARM Processors
I hope you can recommend some suitable voltage stabilizers.
It is required to be powered by a 3.6V battery, which needs to be converted to 3.3V (more than 400mA) and 1.8V (100mA is enough). In order to squeeze out as much power as possible, I hope it can still...
wide Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 394  2467  1236  2386  967  8  50  25  49  20 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号