EEWORLDEEWORLDEEWORLD

Part Number

Search

HRK213E0

Description
Thumb/Pushwheel Switch, Wire Terminal, Thumbwheel Actuator, Panel Mount
CategoryMechanical and electronic products    switch   
File Size359KB,4 Pages
ManufacturerAPEM
Download Datasheet Parametric View All

HRK213E0 Overview

Thumb/Pushwheel Switch, Wire Terminal, Thumbwheel Actuator, Panel Mount

HRK213E0 Parametric

Parameter NameAttribute value
MakerAPEM
Reach Compliance Codecompliant
ECCN codeEAR99
Actuator angle20 deg
Actuator colorGREEN
Actuator length0.748 inch
Actuator materialPOLYAMIDE
Actuator typeTHUMBWHEEL
body width18.0086 mm
Body colorBLACK
body height11.4808 mm
illuminationLED
Manufacturer's serial numberHR
Installation featuresPANEL MOUNT
Maximum operating temperature70 °C
Minimum operating temperature-30 °C
sealEPOXY
surface mountNO
Switch typeTHUMB/PUSHWHEEL SWITCH
Termination typeWIRE
Proportional Hall effect thumbwheels
Distinctive features and specifications
HR series
5 million lifecycles (without detent)
Sealed to IP68
Backlighting option
EMI/RFI shielding
Detent options available
Patented solution
MECHANICAL
Operating Force at center:
2N±0.5N
(without center detent)
4N±0.5N
(with center detent)
Return spring to center
Mechanical operating angle:
±35° (versions S/G/L)
±20° (version K)
• Mechanical
Life: 5 million cycles (without detent)
APEM SAS patented design
ELECTRICAL
• Sensor type:
Hall effect
Supply voltage: 5VDC ± 0.5V
Reverse polarity: -10V max
Overvoltage: +20V max
Return to center voltage (no load): ±0.2V
Consumption:
11 mA max (single output), 22mA max
(dual output)
LED supply: 6VDC 10mA
ENVIRONMENTAL
Operating Temperature: -30°C to +70°C (-22°F to +158°F)
Storage Temperature: -40°C to +85°C (-40°F to +185°F)
Sealing to IP68
Shock resistance: 50g during 11ms
Vibration resistance: 10-500Hz
Salt spray:
IEC 512-6, test 11f
EMI/RF shielding: 100V/m, complies with IEC 61000-
4-3 and ISO 11452-2
ESD: Complies with 16KV EN 61000-4-2
MATERIALS
• Wheel: polyamide with coloring
• Support: polyamide, black
• Electronics sealing: epoxy
• Connector: polyester (Molex 0510210700)
• Multiwire lead: AWG28
NOTES:
Mounting accessories.
Standard hardware includes: 2 self-tapping screws DELTA PT
®
22x08 for
Notice:
Not all part number combinations may be available.
Please refer to the following pages for further information.
Packaging:
Product is available as 20 pieces per package.
plastic
Tolerance: General tolerance for dimensions is
± 0.3 (.012).
Dimensions: First dimensions listed are in mm while inches are shown in brackets.
Note: The company reserves the right to change specifications without notice.
APEM
www.apem.com
It is said that ST has released H7 and F7 for less than 3 US dollars. What do you think?
[i=s]This post was last edited by damiaa on 2018-7-14 12:02[/i] It is said that ST has released H7 and F7 for less than 3 USD. What do you think? 2 USD for 10,000 pieces or more? STM32F730 is even les...
damiaa stm32/stm8
【GD32F310G-START】OLED HELLO EEWORLD——Hardware I2C
【GD32F310G-START】HELLO WORLD - GD32 MCU - Electronic Engineering World - Forum (eeworld.com.cn) Following the serial port driver, after a night of hard work, I finally drove the hardware I2C and submi...
lugl4313820 GD32 MCU
s3c2410 driver confusion!!
Based on the LED driver routine provided by Zhou Ligong's development board and my own understanding of the driver, I made the following modifications, but the driver cannot be implemented. I did not ...
vlonson Embedded System
Show the process of WEBENCH design + high-pass filter design
You can also design high-pass filters in WEBENCH. Just select the high-pass filter in the filter design interface.Enter the required design parameters, click Start Filter Design, and you will get the ...
闲云潭影 Analogue and Mixed Signal
LINK: fatal error LNK1123: failure during conversion to COFF: file invalid or c
I have encountered such a classic problem. I have just been in contact with wince for a week. I have never used MFC to write code and build projects. Instead, I used the program written in Application...
wangbaiqing Embedded System
The device pins are too dense to be soldered.
[i=s] This post was last edited by elvike on 2014-1-4 09:05 [/i] I drew a package of Infineon driver IC 2ED020I12-F2. The pins of this device are very dense, and the soldering method cannot be used to...
elvike PCB Design

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2764  2131  2446  694  2675  56  43  50  14  54 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号