IDT71V2576SA150PF datasheet, PDF

Datasheet> All Categories > IDT71V2576SA150PF

Preview

IDT71V2576SA150PF: Description128K X 36, 256K X 18 3.3V Synchronous SRAMs 2.5V I/O, Pipelined Outputs, Burst Counter, Single Cycle Deselect; File Size285KB，22 Pages; ManufacturerIDT (Integrated Device Technology, Inc.); Websitehttp://www.idt.com/

Download Datasheet View All

IDT71V2576SA150PF Overview

128K X 36, 256K X 18 3.3V Synchronous SRAMs 2.5V I/O, Pipelined Outputs, Burst Counter, Single Cycle Deselect

Preview

Download Datasheet

View All

128K X 36, 256K X 18

3.3V Synchronous SRAMs

2.5V I/O, Pipelined Outputs,

Burst Counter, Single Cycle Deselect

IDT71V2576S

IDT71V2578S

IDT71V2576SA

IDT71V2578SA

Features

128K x 36, 256K x 18 memory configurations

Supports high system speed:

Commercial and Industrial:

– 150MHz 3.8ns clock access time

– 133MHz 4.2ns clock access time

LBO

input selects interleaved or linear burst mode

Self-timed write cycle with global write control (GW), byte write

enable (BWE), and byte writes (BWx)

3.3V core power supply

Power down controlled by ZZ input

2.5V I/O

Optional - Boundary Scan JTAG Interface (IEEE 1149.1

compliant)

Packaged in a JEDEC Standard 100-pin plastic thin quad

flatpack (TQFP), 119 ball grid array (BGA) and 165 fine pitch ball

grid array (fBGA)

Description

The IDT71V2576/78 are high-speed SRAMs organized as 128K x

36/256K x 18. The IDT71V2576/78 SRAMs contain write, data, address

and control registers. Internal logic allows the SRAM to generate a self-

timed write based upon a decision which can be left until the end of the write

cycle.

The burst mode feature offers the highest level of performance to the

system designer, as the IDT71V2576/78 can provide four cycles of data

for a single address presented to the SRAM. An internal burst address

counter accepts the first cycle address from the processor, initiating the

access sequence. The first cycle of output data will be pipelined for one

cycle before it is available on the next rising clock edge. If burst mode

operation is selected (ADV=LOW), the subsequent three cycles of output

data will be available to the user on the next three rising clock edges. The

order of these three addresses are defined by the internal burst counter

and the

LBO

input pin.

The IDT71V2576/78 SRAMs utilize IDT’s latest high-performance

CMOS process and are packaged in a JEDEC standard 14mm x 20mm

100-pin thin plastic quad flatpack (TQFP) as well as a 119 ball grid array

(BGA) and 165 fine pitch ball grid array (fBGA).

Input

Output

Input

I/O

Supply

Synchronous

Asynchronous

Synchronous

N/A

Synchronous

N/A

Synchronous

Asynchronous

Synchronous

N/A

4876 tbl 01

Pin Description Summary

-A

BWE

(1)

CLK

ADV

ADSC

ADSP

LBO

TMS

TDI

TCK

TDO

TRST

I/O

-I/O

, I/O

-I/O

, V

DDQ

Address Inputs

Chip Enable

Chip Selects

Output Enable

Global Write Enable

Byte Write Enable

Individual Byte Write Selects

Clock

Burst Address Advance

Address Status (Cache Controller)

Address Status (Processor)

Linear / Interleaved Burst Order

Test Mode Select

Test Data Input

Test Clock

Test Data Output

JTAG Reset (Optional)

Sleep Mode

Data Input / Output

Core Power, I/O Power

Ground

NOTE:

and

are not applicable for the IDT71V2578.

JUNE 2003

DSC-4876/09

Recommended Resources

Multi-output MEMS clock generator, do you understand it?

Recorder graphic equalizer drive circuit

Single channel multifunctional radio transmitter schematic diagram

DC and DC converter circuit diagram using thyristor b

Asynchronous decimal counter using set method

Fax machine circuit diagram 2

[Exchange Chip Coins for AVR Learning Boards and Programmers] Event Post (Event has ended): Summer Cool Learning , isn't this a cool name? Use your ChipCoins to exchange for AVR learning boards and programmers. Details are as follows:STEP 1: How to exchange AVR learning board and programmer?...; tiankai001 Microchip MCU

How to pass the packets captured by passthru to the application?: How to pass the packets captured by passthru to the application?...; zsmbj Embedded System

How to choose "common switching power supply chips": [size=5]When choosing a power IC, one must not only consider circuit performance requirements and reliability, but also its size, weight, battery life extension, and cost. Here are some basic selectio...; Jacktang Analogue and Mixed Signal

A poor rookie's request for help: RT, I am not a student majoring in electronics, but I need to use MSP430+MLX90615 in my graduation project. According to the datasheet, I asked someone to solder the circuit. Can any kind-hearted pers...; dragon87211 Microcontroller MCU

Keithley Lecture: Teach you how to send emails in KTXE: Test and measurement engineers, you must have had this feeling, it usually takes several days to deal with the large number of delays or failures caused by the loss of control of key parameter measure...; Jack_ma Test/Measurement

The motor burned out: The electric double beam bridge crane 10 tons A6 lifting motor 22KW peripheral circuit has been tested with a multimeter. There is no problem. There is no phase loss phenomenon. At first, I suspected ...; eeleader Industrial Control Electronics

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components