EEWORLDEEWORLDEEWORLD

Part Number

Search

D-SUB-205AE37SRNDBY2

Description
D Type Connector, 37 Contact(s), Female, 0.109 inch Pitch, Solder Terminal, M2.6, Plug
CategoryThe connector    The connector   
File Size124KB,1 Pages
ManufacturerPalPilot
Environmental Compliance
Download Datasheet Parametric View All

D-SUB-205AE37SRNDBY2 Overview

D Type Connector, 37 Contact(s), Female, 0.109 inch Pitch, Solder Terminal, M2.6, Plug

D-SUB-205AE37SRNDBY2 Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerPalPilot
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresROHS COMPLIANT,HEX-SCREWS
body width0.492 inch
subject depth0.492 inch
body length2.732 inch
Body/casing typePLUG
Contact to complete cooperationGOLD (3) OVER NICKEL (50)
Contact completed and terminatedTin (Sn) - with Nickel (Ni) barrier
Contact point genderFEMALE
Contact materialCOPPER ALLOY
contact modeSTAGGERED
Contact resistance15 mΩ
Contact styleRND PIN-SKT
Dielectric withstand voltage1000VAC V
Insulation resistance3000000000 Ω
Insulator colorBLUE
insulator materialPOLYAMIDE
JESD-609 codee3
Manufacturer's serial number205
Plug contact pitch0.109 inch
Match contact row spacing0.112 inch
Installation option 1M2.6
Installation option 2RIVET
Installation methodRIGHT ANGLE
Installation typeBOARD
PCB row number2
Number of rows loaded2
Maximum operating temperature105 °C
Minimum operating temperature-55 °C
PCB contact patternSTAGGERED
PCB contact row spacing2.8448 mm
Plating thickness3u inch
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Shell surfaceNICKEL
Shell materialSTEEL
Terminal length0.125 inch
Terminal pitch2.7686 mm
Termination typeSOLDER
Total number of contacts37
Why does my mobile phone's WIFI consume much more power than 3G?
I accidentally turned on the WIFI on my phone and found that the battery was used up immediately. I didn't use WIFI for anything. But the power consumption is huge. I usually turn on 3G, but the actua...
John_sea RF/Wirelessly
Why can USB be hot-swapped?
It seems to be because the power supply is inserted before or after the signal line? ? ? I remember that some people often hot-plug hard drives or other things because of this reason. As long as they ...
262476547 Embedded System
Teaching requirements for the course "Analog Circuit Design" for the major of electronic information engineering
[:P]Teaching requirements for the course "Analog Circuit Design" for the major of electronic information engineering1. Basic requirementsCarry out teaching according to the requirements of the Outline...
fighting Analog electronics
Without a SECTIONS specification appears, but the .out file is generated. Can it be ignored?
The specific warning is: warning #10247-D: creating output section "reset_vec" without a SECTIONS specification. What is the reason? Is there any solution? Thank you....
jonny0811 Microcontroller MCU
Development of a portable low-frequency amplitude-frequency characteristic tester
Abstract : This paper introduces an amplitude-frequency characteristic tester based on single-chip microcomputer control, which is used to measure the amplitude-frequency characteristics of active and...
fighting Test/Measurement
How to call dynamic link library under EVC?
In VS2005, you can easily use references, add the DLL file, and then add a using *** to use the classes and functions in the library. Is there a corresponding method in EVC to achieve this?...
wfkj Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2168  81  2582  2089  2694  44  2  52  43  55 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号