177-714-2-9GS4K1-24FNN datasheet, PDF

Datasheet> All Categories > The connector> The connector> 177-714-2-9GS4K1-24FNN

177-714-2-9GS4K1-24FNN: DescriptionInterconnection Device; CategoryThe connector The connector; File Size436KB，4 Pages; ManufacturerGlenair; Websitehttp://www.glenair.com/

Download Datasheet Parametric View All

177-714-2-9GS4K1-24FNN Overview

Interconnection Device

177-714-2-9GS4K1-24FNN Parametric

Parameter Name	Attribute value
Reach Compliance Code	compli
Connector type	INTERCONNECTION DEVICE
Base Number Matches	1

Preview

Download Datasheet

View All

MWDM Micro-D Shielded Cable Assemblies

Single-Ended or Double-Ended–These

easy-to-order cable

assemblies eliminate the need for expensive assembly

labor. 100% tested and ready for use.

Now With Twisted Pairs–No

need to create a procurement

speciﬁcation for Micro-D cables with twisted pairs. Glenair

177-740 cables are furnished with a full complement of

white/blue twisted pair wires.

Integral Shield Termination–The

connector shell has a

platform to accept Band-It shield termination bands. The

cable shield braid is attached directly to the connector.

Save Labor, Reduce Weight and Improve EMI Shielding with

Glenair’s Micro-D Shielded Cable Assemblies

Aerospace electronics systems require higher and higher levels of protection from radiated emissions. Glenair’s fully

shielded Micro-D cable assemblies meet this need. The cable shield is attached directly onto the one-piece connector

shell and secured with a stainless steel

BAND-IT

® clamp. These pre-wired, 100% tested assemblies meet the

requirements of MIL-DTL-83513. An optional ground spring on the pin connector assures low shell-to-shell resistance.

Available with a variety of wire types and shields, Micro-D shielded assemblies can be ordered in any length, either

single-ended or “back-to-back”.

Ground Spring and EMI Shielding Effectiveness

– A gold-plated

stainless steel ground spring on the pin connector mating face offers

substantial improvement in EMI protection. The graphs compare

identical connectors tested with and without ground springs.

EMI Performance with Ground Spring

SHIELDING EFFECTIVENESS (DB)

100

1.00E+03

100

1.00E+03

EMI Performance without Ground Spring

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

1.00E+04

1.00E+05

1.00E+06

1.00E+07

1.00E+08

1.00E+09

FREQUENCY (Hz)

CAGE Code 06324/0CA77

Printed in U.S.A.

GLENAIR, INC. • 1211 AIR WAY • GLENDALE, CA 91201-2497 • 818-247-6000 • FAX 818-500-9912

www.glenair.com

B-8

E-Mail: sales@glenair.com

Recommended Resources

Improved connection method of triode switch circuit circuit diagram

Pulse signal generating circuit d

JJW2 series AC purification stabilized power supply circuit

TDA7293 high efficiency class G amplifier circuit

Multifunctional display LCD display chip circuit

Eight-level telecommunications filter circuit

cepc+eboot cannot download nk, please help me.: I am using a pcm3370 board and want to start nk via eboot. 1. Use a cf card to make a dos boot disk 2. Start cepc and enter dos, then select the second option: . . 2. CEPC_1024, Boot CE/PC (ether via ...; ttyugg Embedded System

I have a question about the bit number of bit_vector in VHDL: Is a(0) the first bit counted from the left or the right?: I have a question about the bit number of bit_vector in VHDL: a: bit_vector (7 downto 0) So is a (0) the first bit counted from the left or the right of a?...; batmancar Embedded System

IC headhunter (Beijing)firmware system engineer: jonathan@chinaeejob.com1. Firmware ucode development experience using ARM9 and/or MIPS microprocessors in assembly, C and C++. 2. Must have hands-on experience with design and implementation of video/...; zouxianzhao Embedded System

The GS voltage is 0, why is there still voltage output?: [backcolor=white]IRF9640 PMOS output. [/backcolor] [backcolor=white] When the GS voltage is less than -4V, it is turned on and the current flows from S to D. When GS is 0, the PMOS should be turned of...; stm32f103vct6 Analog electronics

Development of IC bus and IC configuration and simulation: This article mainly introduces the development of IC bus and IC configuration and simulation to simplify the communication between the master and slave devices on the bus. The application examples pro...; tiankai001 MCU

How do you perform system requirement analysis in SOPC?: We know that before designing a SOPC system, we must determine the system requirements, such as the computing power required by the application system, the required bandwidth and throughput, the requi...; shilaike FPGA/CPLD

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components