B15KP-AC datasheet, PDF - EEWORLD Datasheet

B15KP-AC: DescriptionToggle Switch, SPDT, On-(on), Horizontal, 3 PCB Hole Cnt, Solder Terminal, Paddle Actuator, Through Hole-straight; CategoryMechanical and electronic products switch; File Size1MB，7 Pages; ManufacturerNKK Switches; Environmental Compliance

Download Datasheet Parametric View All

B15KP-AC Overview

Toggle Switch, SPDT, On-(on), Horizontal, 3 PCB Hole Cnt, Solder Terminal, Paddle Actuator, Through Hole-straight

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Maker	NKK Switches
Reach Compliance Code	not_compliant
ECCN code	EAR99
Actuator angle	26 deg
Actuator color	RED
Actuator length	0.406 inch
Actuator material	NYLON
Actuator type	PADDLE
body width	6.8072 mm
Body color	BLACK
body height	26.5176 mm
Body length or diameter	8.7884 mm
Casing diameter	0.236 inch
Nozzle length	0.138 inch
Casing type	UNTHREADED
center contact material	PHOSPHOR BRONZE
Center contact plating	GOLD OVER SILVER
Contact (DC) maximum rated power R load	0.4VA@28VDC
Contact function	ON-(ON)
Contact resistance	0.05 mΩ
Dielectric withstand voltage	500VAC V
Electrical life	50000 Cycle(s)
End contact material	BRASS
End contact plating	GOLD OVER NICKEL
Insulation resistance	500000000 Ω
insulator material	GLASS FILLED POLYAMIDE
JESD-609 code	e4
Manufacturer's serial number	B
Installation features	THROUGH HOLE-STRAIGHT
Maximum operating temperature	70 °C
Minimum operating temperature	-25 °C
PCB hole count	3
seal	EPOXY
Solderability	WAVE
surface mount	NO
Switch action	HORIZONTAL
switch function	SPDT
Switch type	TOGGLE SWITCH
Terminal surface	Gold (Au) - with Nickel (Ni) barrier
Terminal length	0.122 inch
Terminal material	BRASS
Termination type	SOLDER
Washability	SOLVENT

Detailed explanation of assembly instructions: Detailed explanation of assembly instructions...; 安_然 DSP and ARM Processors

After copper plating, DRC reports an error: There are both analog and digital grounds on the board. When laying copper, part of it is digital ground and part of it is analog ground. When performing DRC check, the following dialog box appears. I...; emily_1105 PCB Design

Beginner Programmer's Guide: uC/OS-II user manual is here: uC/OS-II Introduction uC/OS-II is a priority-based preemptive hard real-time kernel. Since its release in 1992, it has been widely used all over the world. It is a kernel designed specifically for emb...; jingcheng ARM Technology

Reduce noise and interference: Reduce noise and interference 1) If you can use a low-speed chip, don't use a high-speed one. Use high-speed chips in key places. (2) You can use a resistor in series to reduce the jump rate of the co...; decho0821 RF/Wirelessly

My EK-LM3S811-ND Rev2 cannot download and debug: I installed the driver according to the LM3S811EVALUATION KIT README FIRST in the LM3S811 TI Evaluation kit CD. After installation, the driver name is different from that in the documentation. The doc...; WINKLE Microcontroller MCU

DSP2812 uses CCS3.3 to connect to the emulator to flash the program? ? ?: I use CCS3.3 to connect the emulator XDS510-USB2.0 to flash the program to 2812. The software and emulator are normal, and there is no problem in flashing the program normally. Recently, the error ala...; sdwulijie2010 DSP and ARM Processors

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components