306F-611-3103 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > The connector> The connector> 306F-611-3103

306F-611-3103: DescriptionBoard Connector, 11 Contact(s), 1 Row(s), Male, Right Angle, 0.156 inch Pitch, Solder Terminal, Natural Insulator, Receptacle; CategoryThe connector The connector; File Size173KB，1 Pages; ManufacturerMethode Electronics Inc.

Download Datasheet Parametric View All

306F-611-3103 Overview

Board Connector, 11 Contact(s), 1 Row(s), Male, Right Angle, 0.156 inch Pitch, Solder Terminal, Natural Insulator, Receptacle

306F-611-3103 Parametric

Parameter Name	Attribute value
Maker	Methode Electronics Inc.
Reach Compliance Code	unknown
ECCN code	EAR99
Other features	WITH LOCKING RAMP
subject depth	0.45 inch
body length	1.71 inch
Body/casing type	RECEPTACLE
Connector type	BOARD CONNECTOR
Contact to complete cooperation	AU ON NI
Contact completed and terminated	TIN OVER NICKEL
Contact point gender	MALE
Contact material	BRASS
contact mode	RECTANGULAR
Contact resistance	5 mΩ
Contact style	SQ PIN-SKT
Dielectric withstand voltage	1500VAC V
maximum insertion force	LIF N
Insulation resistance	500000000000 Ω
Insulator color	NATURAL
insulator material	NYLON
Manufacturer's serial number	3000
Plug contact pitch	0.156 inch
Installation method	RIGHT ANGLE
Installation type	BOARD
Number of connectors	ONE
PCB row number	1
Number of rows loaded	1
Maximum operating temperature	105 °C
Minimum operating temperature	-40 °C
PCB contact pattern	RECTANGULAR
Plating thickness	30u inch
Rated current (signal)	7 A
Guideline	UL, CSA
reliability	COMMERCIAL
Terminal length	0.156 inch
Terminal pitch	3.9624 mm
Termination type	SOLDER
Total number of contacts	11
Evacuation force-minimum value	LIF N

Preview

Download Datasheet

View All

.156” (3.96mm)

Through Hole Right Angle Connector

3000 SERIES “TERMACON”

PART NUMBER LEGEND

30XX-XXX-XXXX

CONTACT TAIL DIMS (SEE TABLE 2)

CONTACT MATERIAL (SEE NOTE 1)

OPTIONS

2 - HIGH INSERTION FORCE CONTACT

3 - LOW INSERTION FORCE CONTACT

NO. OF POSITONS (SEE TABLE 1)

OPTIONS

WITH LEGS

WITH HOOKS

WITH HOOKS AND LOCKING RAMP

WITH LOCKING RAMP

WITH HOOKS, LOCKING RAMP AND POLARIZING KEY

WITHOUT HOOKS, W/ LOCKING RAMP AND POLARIZING KEY

CONTACT FINISH (SEE NOTE 2)

INSULATOR MATERIAL (SEE NOTE 1)

MATING HEADERS: 3100 SERIES

POLARIZING KEY &

LOCKING RAMP

LEG

HOOK

Connector Products

1700 Hicks Road • Rolling Meadows, IL 60008 USA

Telephone: 847.392.3500 • Fax: 847.392.9404

email: mcpsales@methode.com • Web Page: www.methode.com

Recommended Resources

High-power lantern chain circuit with adjustable lighting frequency for each group a

Lighting delay light off circuit 2 using 555 time base integrated circuit

One-way energy consumption braking circuit a

Basic circuit diagram of switching power supply AC input and rectification and filtering

Sinusoidal signal phase meter circuit

Single chip voice recording and playback integrated circuit

What filter is suitable for DDS?: Hello everyone: The DDS I am using now is AD9833. As shown in the figure above, the output uses an inverting amplifier to amplify the sine wave, but I found that the waveform has a sawtooth component....; PSIR Analog electronics

Issues to pay attention to in PCB design: Priority, control line, memory, wiring Issues to be noted in PCB design The purpose of PCB design should be clear. For important signal lines, the length of wiring and processing ground loops should b...; xhxyd PCB Design

How to program a microcontroller well (8): 15. The Cultivation of Modifying Other People's Programs ------------ When you maintain other people's programs, please do not delete or modify existing programs in a very subjective way. I often see ...; yuandayuan6999 MCU

stm8 detects the falling edge of the port pulse: A square wave pulse enters the port. Now we need to determine its falling edge. Which one takes less time, external interrupt or input capture?...; sang523 stm32/stm8

Question about the working state of TTL inverter transistor: In this figure, when the input voltage is a high level of 3.6V, why are T2 and T3 in a saturated state instead of an amplified state?...; pvnana Analog electronics

How to select the pop-up interface mode: Now I am developing a PDA using WIN CE. I want to pop up a pre-set interface by clicking a certain button. How can I set it up? As a cutting version, the smart device form is too different from creati...; ydm123ydm Embedded System

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components