EEWORLDEEWORLDEEWORLD

Part Number

Search

212Y1002N228FN

Description
Rotary Switch, 2 Positions, 10PDT, Latched, 0.25A, 28VDC, Solder Terminal, Flat Shaft Trim Actuator, Through Hole-straight, ROHS COMPLIANT
CategoryMechanical and electronic products    switch   
File Size1MB,3 Pages
ManufacturerCTS
Environmental Compliance
Download Datasheet Parametric View All

212Y1002N228FN Overview

Rotary Switch, 2 Positions, 10PDT, Latched, 0.25A, 28VDC, Solder Terminal, Flat Shaft Trim Actuator, Through Hole-straight, ROHS COMPLIANT

212Y1002N228FN Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
package instructionROHS COMPLIANT
Reach Compliance Codeunknow
ECCN codeEAR99
Actuator typeFLAT SHAFT TRIM
body height20.19 mm
Body length or diameter26.98 mm
Maximum contact current (DC)0.25 A
Contact (DC) maximum rated R load.25A@28VDC
Maximum contact voltage (DC)28 V
Electrical life25000 Cycle(s)
JESD-609 codee4
Manufacturer's serial number212
Installation featuresTHROUGH HOLE-STRAIGHT
Number of positions2
Number of switching segments1
surface mountNO
Switch actionLATCHED
switch function10PDT
Switch typeROTARY SWITCH
Terminal surfaceSilver (Ag)
Termination typeSOLDER
Base Number Matches1
Panel Seal
Available with bushing and shaft seal
1
4
3 05 14
AM3359 ICE development board running powerlink on Linux
Hi, I have a TI AM3359 ICE development board. I have completed the Linux system porting. I want to run the Powerlink protocol on Linux. However, the network implementation of this board does not suppo...
simonls Linux and Android
V853 Replace the startup LOGO
# The overview mainly describes how to replace the startup LOGO of V853 # Environmental software: V853 Tina 5.0 SDK Hardware: Allwinner V853 development board # Specific steps First, let's take a look...
aleksib Domestic Chip Exchange
Dear big brothers, please help me
module flash_mod(clk,rst,LED_OUT); input clk; inout rst; outputLED_OUT; //----------------------// reg [19:0]cnt; reg led_out; parameter T50ms=20'd999_999; //-------------------------// //------------...
xander_wang FPGA/CPLD
The problem of the servo not rotating when the nodemcu esp8266 development board drives it
[i=s]This post was last edited by xiguabuda on 2022-3-11 22:59[/i]I'm new to this. I'm using a development board and MicroPython to drive the servo, but there's no response. Could you please help me f...
xiguabuda MicroPython Open Source section
Mentor Usage Problems
Dear experts, after installing Mentor DC7.9.2, when Capture Design calls the component library, it cannot be displayed, but the component library can be opened separately. Is there any problem with th...
随风飘啊 PCB Design
Ask about the interrupt response speed
Hello everyone, I have been busy with the WM project recently and have not been online for a long time. I encountered a problem today and I would like to ask you for help. I hope you can give me some ...
huzhiming Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2119  714  1717  945  2924  43  15  35  20  59 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号