151308-805206-TH datasheet, PDF

151308-805206-TH: DescriptionHEADER CONNECTOR,PCB MNT,RECEPT,8 CONTACTS,PIN,0.079 PITCH,PC TAIL TERMINAL,BLACK; CategoryThe connector The connector; File Size223KB，3 Pages; Manufacturer3M; Websitehttp://3M.com/esd

Download Datasheet Parametric View All

151308-805206-TH Overview

HEADER CONNECTOR,PCB MNT,RECEPT,8 CONTACTS,PIN,0.079 PITCH,PC TAIL TERMINAL,BLACK

Parameter Name	Attribute value
Maker	3M
Reach Compliance Code	unknown
ECCN code	EAR99
Other features	OPTIONAL SECOND INSULATOR
body width	0.155 inch
subject depth	0.059 inch
body length	0.295 inch
Body/casing type	RECEPTACLE
Connector type	BOARD CONNECTOR
Contact to complete cooperation	AU ON NI
Contact completed and terminated	GOLD
Contact point gender	MALE
Contact material	COPPER ALLOY
contact mode	RECTANGULAR
Contact style	SQ PIN-SKT
Dielectric withstand voltage	500VDC V
Insulation resistance	5000000000 Ω
Insulator color	BLACK
insulator material	LIQUID CRYSTAL POLYMER (LCP)
Manufacturer's serial number	1513
Plug contact pitch	0.079 inch
Match contact row spacing	0.079 inch
Installation method	STRAIGHT
Installation type	BOARD
Number of connectors	ONE
PCB row number	2
Number of rows loaded	2
Maximum operating temperature	105 °C
Minimum operating temperature	-55 °C
PCB contact pattern	RECTANGULAR
PCB contact row spacing	2.0066 mm
Plating thickness	15u inch
Rated current (signal)	1.5 A
Guideline	UL
reliability	COMMERCIAL
Terminal length	0.161 inch
Terminal pitch	2.0066 mm
Termination type	SOLDER
Total number of contacts	8

How to determine the end of ADC and what impact does the ADC conversion cycle have on accuracy?: 1. My program uses DMA1 for transmission. How do I determine the end of ADC?Should I determine it inthe void DMA1_Channel1_IRQHandler(void){}function?How should I do it?2. What is the impact of ADC co...; lingr stm32/stm8

【allegro】The routing between two components is not correct: As shown in the picture:Why can't the line be pushed straight in this place? ? Help, help~~...; ohahaha PCB Design

I found a document about A/D noise performance. Please read it (2): [b]Use noise dithering to improve the spurious-free dynamic range of the ADC[/b] Spurious-free dynamic range (SFDR) is the ratio of the RMS signal amplitude to the RMS value of the largest spurious sp...; linda_xia Analog electronics

Regarding "Circuit Design Based on Operational Amplifiers and Analog Integrated Circuits", there is a concept of "Pole" that is not clear: [i=s]This post was last edited by sunboy25 on 2020-10-8 23:15[/i]I would like to ask, is the place where I drew the red circle in the picture above correct as described in the book? Why do I feel that...; sunboy25 Analog electronics

RISC-V IDE MRS usage notes (Part 3): Improving floating-point calculation efficiency: MRS has built-in CH32V30X series chips. This series of chips supports FPU (floating point unit). If you want to turn it on, you need to enable the corresponding extension, as shown in the figure below...; Moiiiiilter MCU

Pan it STM32H750 3 (lan8720 Ethernet test --iperf): [font=宋体][size=4] When debugging lan8720 hardware, you need to check whether the ground pad is cold soldered, whether the internal voltage regulator 1.2V has output, and whether it has output 50M freq...; RCSN stm32/stm8

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components