EEWORLDEEWORLDEEWORLD

Part Number

Search

BTB-30-01-GF-D-250

Description
Board Connector, 60 Contact(s), 2 Row(s), Male, Straight, 0.079 inch Pitch, Solder Terminal, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size292KB,1 Pages
ManufacturerSAMTEC
Websitehttp://www.samtec.com/
Download Datasheet Parametric View All

BTB-30-01-GF-D-250 Overview

Board Connector, 60 Contact(s), 2 Row(s), Male, Straight, 0.079 inch Pitch, Solder Terminal, Black Insulator, Receptacle

BTB-30-01-GF-D-250 Parametric

Parameter NameAttribute value
MakerSAMTEC
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresPCB STACKING CONNECTOR
body width0.157 inch
subject depth0.15 inch
body length2.37 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON NI
Contact completed and terminatedGOLD
Contact point genderMALE
Contact materialBRASS
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Dielectric withstand voltage1000VAC V
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialLIQUID CRYSTAL POLYMER (LCP)
Manufacturer's serial numberBTB
Plug contact pitch0.079 inch
Match contact row spacing0.079 inch
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature105 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.0066 mm
Plating thickness3u inch
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.1 inch
Terminal pitch2.0066 mm
Termination typeSOLDER
Total number of contacts60
Vllink lite hardware design information
[i=s]This post was last edited by le062 on 2018-11-5 05:53[/i] The Vllink lite hardware made with GD32F350 is very simple: [list=1] [*]One SPI to implement SWD timing[*]Two SPI master-slave cooperatio...
le062 GD32 MCU
On procedural issues
CapResult_H=0x0B; //*Data; //AD7747_Conversion_Result[1]; Data++; CapResult_M=0x70; //*Data; //AD7747_Conversion_Result[2]; Data++; ]; UartTX_Send_Byte(CapResult_H); UartTX_Send_Byte(CapResult_M); Uar...
小兵小将 RF/Wirelessly
How to set the system sound channel in wince? Thanks!
How to set the system sound channel in wince? Thank you very much...
redmonster Embedded System
Discussion on the Self-oscillation of Voltage-controlled Voltage Source Second-order Low-pass Filter
The circuit diagram is as follows, the characteristic frequency is 100kHz. Adjust R1 to make the amplification factor 3, and the circuit will produce self-excited oscillation.Transient response, the t...
寅子敬 Analog electronics
DS1302 clock chip multi-byte transmission problem
Question: Does multi-byte transmission require 8 bytes? The program is as follows: SCLK BIT P1.3 IO_DATA BIT P1.4 RST BIT P1.5 BitCnt data 30h ; Data bit counter ByteCnt data 31h ; Data byte counter C...
thinking小铺 MCU
Asynchronous reset counter
Question: I want to implement an asynchronous counter on CPLD, which requires a count of +1 on both the rising and falling edges of the clock. The code is as follows: reg[7:0] counter; always @(clk) b...
zhoulm Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2415  1687  1735  2238  1302  49  34  35  46  27 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号