3008-004-3004 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > The connector> The connector> 3008-004-3004

3008-004-3004: DescriptionBoard Connector, 4 Contact(s), 1 Row(s), Male, Right Angle, 0.156 inch Pitch, Solder Terminal, Natural Insulator, Receptacle; CategoryThe connector The connector; File Size173KB，1 Pages; ManufacturerMethode Electronics Inc.

Download Datasheet Parametric View All

3008-004-3004 Overview

Board Connector, 4 Contact(s), 1 Row(s), Male, Right Angle, 0.156 inch Pitch, Solder Terminal, Natural Insulator, Receptacle

3008-004-3004 Parametric

Parameter Name	Attribute value
Maker	Methode Electronics Inc.
Reach Compliance Code	unknown
ECCN code	EAR99
Other features	WITH LEGS
body width	0.41 inch
subject depth	0.45 inch
body length	0.618 inch
Body/casing type	RECEPTACLE
Connector type	BOARD CONNECTOR
Contact to complete cooperation	AU ON NI
Contact completed and terminated	TIN OVER NICKEL
Contact point gender	MALE
Contact material	PHOSPHOR BRONZE
contact mode	RECTANGULAR
Contact resistance	5 mΩ
Contact style	SQ PIN-SKT
Dielectric withstand voltage	1500VAC V
maximum insertion force	LIF N
Insulation resistance	500000000000 Ω
Insulator color	NATURAL
insulator material	NYLON
Manufacturer's serial number	3000
Plug contact pitch	0.156 inch
Installation method	RIGHT ANGLE
Installation type	BOARD
Number of connectors	ONE
PCB row number	1
Number of rows loaded	1
Maximum operating temperature	105 °C
Minimum operating temperature	-40 °C
PCB contact pattern	RECTANGULAR
Plating thickness	20u inch
Rated current (signal)	7 A
Guideline	UL, CSA
reliability	COMMERCIAL
Terminal length	0.218 inch
Terminal pitch	3.9624 mm
Termination type	SOLDER
Total number of contacts	4
Evacuation force-minimum value	LIF N

Preview

Download Datasheet

View All

.156” (3.96mm)

Through Hole Right Angle Connector

3000 SERIES “TERMACON”

PART NUMBER LEGEND

30XX-XXX-XXXX

CONTACT TAIL DIMS (SEE TABLE 2)

CONTACT MATERIAL (SEE NOTE 1)

OPTIONS

2 - HIGH INSERTION FORCE CONTACT

3 - LOW INSERTION FORCE CONTACT

NO. OF POSITONS (SEE TABLE 1)

OPTIONS

WITH LEGS

WITH HOOKS

WITH HOOKS AND LOCKING RAMP

WITH LOCKING RAMP

WITH HOOKS, LOCKING RAMP AND POLARIZING KEY

WITHOUT HOOKS, W/ LOCKING RAMP AND POLARIZING KEY

CONTACT FINISH (SEE NOTE 2)

INSULATOR MATERIAL (SEE NOTE 1)

MATING HEADERS: 3100 SERIES

POLARIZING KEY &

LOCKING RAMP

LEG

HOOK

Connector Products

1700 Hicks Road • Rolling Meadows, IL 60008 USA

Telephone: 847.392.3500 • Fax: 847.392.9404

email: mcpsales@methode.com • Web Page: www.methode.com

Recommended Resources

High power tube power amplifier 01

Simple portable TV field strength meter circuit

Single chip 1000Hz sawtooth wave circuit

Typical circuit when M57962L drives high-power IGBT module

A self-restoring overvoltage protection circuit

Wince5.0 about generating NK.nbo: I cannot generate NK.nbo under WINCE5.0. Later, I read related articles online and learned that I need to modify the config.bib file and add the following parameters: ROMSTART ROMWIDTH ROMSIZE ROMSIZE...; znlg37 Embedded System

Using TINA simulation, why is there such a big difference between the amplifier output current and the power supply current?: The circuit diagram is as shown in the figure. The power amplifier is OPA544, the power supply is ±12V, the input of the same direction input is 4V, the gain G=+1.5, the output voltage is 6V, the load...; zpccx Analog electronics

Driver development under wince: We designed a board using SAMSUNG's ARM chip S3C2440. The hardware schematic diagram referred to the same chip development board from Langcheng. We added an FPGA, which is connected to the ARM bus in ...; hflf35 Embedded System

Program problem during wince serial communication.: I used C# to write a program, referring to other people's experience, using the CREATEFILE function, with the following three parameters: private const uint GENERIC_READ = 0x80000000; private const ui...; janeyqian Embedded System

Application of single chip microcomputer control system in EDM machine tool: 1 IntroductionAt present, in the oil pump nozzle industry, most of the traditional nozzle processing relies on manual operation determined by personal skills, with unstable product quality, low produc...; fighting MCU

How do I set pin 1 of port b to high or low level?: How do I set pin 1 of port b to high or low level? This is my procedure: LIST P=PIC16F870 #includep16f870.inc ;Include header file to avoid register definitionorg 00hGOTO MAINORG 05H MAINBANKSEL TRISB...; rsszd Microchip MCU

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components