Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/
3483fc
2
LT3483/LT3483A
ELECTRICAL CHARACTERISTICS
PARAMETER
V
IN
Operating Range
V
IN
Undervoltage Lockout
FB Comparator Trip Voltage to GND (V
FB
)
FB Output Current (Note 3)
FB Comparator Hysteresis
Quiescent Current in Shutdown
Quiescent Current (Not Switching)
I
FB
Line Regulation
Switch Off-Time
Switch Current Limit
Switch V
CESAT
Switch Leakage Current
D Pin Current Limit
Rectifier Leakage Current
Rectifier Forward Drop
SHDN Input Low Voltage
SHDN Input High Voltage
SHDN Pin Current
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings may
cause permanent damage to the device. Exposure to any Absolute Maximum
Rating condition for extended periods may affect device reliability and
lifetime.
1.5
6
10
D = – 40V
I
D
= 150mA to GND
0.64
0.4
LT3483
LT3483A
I
SW
= 150mA to GND
SW = 40V
350
4
170
340
FB Falling
FB = V
FB
– 5mV
FB Rising
V
SHDN
= GND
FB = –0.05V
2.5V ≤ V
IN
≤ 16V
300
200
400
200
1
230
460
40
●
●
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C. V
IN
= 3.6V, V
SHDN
= 3.6V unless otherwise specified.
CONDITIONS
MIN
2.5
2
0
–10.2
5
–10
10
1
50
0.07
TYP
MAX
16
2.4
12
–9.7
UNITS
V
V
mV
µA
mV
µA
µA
%/V
ns
mA
mA
mV
µA
mA
µA
V
V
V
µA
Note 2:
The LT3483E/LT3483AE are guaranteed to meet specifications from
0°C to 85°C. Specifications over the –40°C to 85°C operating temperature
range are assured by design, characterization and correlation with
statistical process controls. The LT3483I/LT3483AI are guaranteed to meet
specifications over the –40°C to 125°C operating temperature range.
Note 3:
Current flows out of the pin.
3483fc
3
LT3483/LT3483A
TYPICAL PERFORMANCE CHARACTERISTICS
V
FB
Current
10.2
16
V
FB
Voltage
400
350
SWITCH OFF TIME (ns)
–25
50
75
0
25
TEMPERATURE (°C)
100
125
Switch Off Time
10.1
V
FB
CURRENT (µA)
V
FB
VOLTAGE (mV)
12
300
250
200
150
100
50
10.0
8
9.9
4
9.8
–50
–25
50
75
0
25
TEMPERATURE (°C)
100
125
0
–50
0
–50
–25
0
25
75
50
TEMPERATURE (°C)
100
125
3483 G01
3483 G02
3483 G03
Switch Current Limit (LT3483)
230
220
210
200
190
180
170
–50
CURRENT LIMIT (mA)
420
440
Switch Current Limit (LT3483A)
SWITCH CURRENT LIMIT (mA)
400
380
–25
0
25
50
75
TEMPERATURE (°C)
100
125
360
–50
–25
50
75
0
25
TEMPERATURE (°C)
100
125
3483 G04
3483 G07
Quiescent Current
50
SHDN
PIN BIAS CURRENT (µA)
10
8
SHDN
Pin Bias Current
T
A
= 25°C
QUIESCENT CURRENT (µA)
40
30
6
4
20
10
2
0
–50
–25
50
75
0
25
TEMPERATURE (°C)
100
125
0
0
8
4
12
SHDN
PIN VOLTAGE (V)
16
3483 G06
3483 G05
3483fc
4
LT3483/LT3483A
PIN FUNCTIONS
(DFN/TSOT-23)
FB (Pin 1/Pin 3):
Feedback. Place resistor to negative
output here. Set resistor value R1 = V
OUT
/10µA.
GND (Pins 2, 3/Pin 2):
Ground. For DFN package, tie both
pin 2 and pin 3 together to ground.
SW (Pin 4/Pin 1):
Switch. Connect to external inductor
L1 and positive terminal of transfer capacitor.
V
IN
(Pin 5/Pin 6):
Input Supply. Must be locally bypassed
with 1µF or greater.
NC (Pin 6/NA):
No Internal Connection.
D (Pin 7/Pin 5):
Anode Terminal of Integrated Schottky
Diode. Connect to negative terminal of transfer capaci-
tor and external inductor L2 (flyback configuration) or
to cathode of external Schottky diode (inverting charge
pump configuration).
SHDN
(Pin 8/Pin 4):
Shutdown. Connect to GND to turn
device off. Connect to supply to turn device on.
Exposed Pad (Pin 9/NA):
GND. The exposed pad should
be soldered to the PCB ground to achieve the rated thermal
[size=4] PCB designers may design a printed circuit board with an odd number of layers. [/size] [size=4] [/size] [size=4] If the routing doesn't require an extra layer, why use it? Wouldn't reducing t...
1. Enable scene level control
2. Parent-child tree and classification object attribute tree
3. Switch scene level
After loading the park in the 3D visualization scene, the system will automatically cr...
When CC1200 receives data packets, the synchronization word can be received, but when reading the number of received bytes RXBYTES, it is often 0, resulting in packet loss. Which registers need to be ...
When running the enet_uip routine of 9B96, when using static IP, the IP address is displayed on the screen. However, when the IP address is entered on the web page, it cannot be displayed. . . Can som...
Serial port debugging of the microcontroller is very convenient. Of course, this is also one of the commonly used debugging methods. Let's take a look at the serial port related to Nucleo-F413ZH: [ali...
PCB Design
京公网安备 11010802033920号
EEWORLD
