Storage Temperature Range...................–65°C to 150°C
Lead Temperature (Soldering, 10 sec)
FE Package ....................................................... 300°C
PIN CONFIGURATION
TOP VIEW
C
WDT
FB1
RUN/SS1
BST1
SW1
DA1
V
IN
CONFIG
DA2
SW2
1
2
3
4
5
6
7
8
9
25
GND
24 EN/UVLO
23 SYNC
22 RT
21 C
WDT
20 C
POR1
19 BIAS
18 C
POR2
17 WDI
16
WDE
15
WDO
14
RST1
13
RST2
RT 1
SYNC 2
EN/UVLO 3
FB1 4
RUN/SS1 5
BST1 6
7
SW1
8
DA1
9 10 11 12
CONFIG
DA2
SW2
V
IN
25
GND
TOP VIEW
C
POR1
C
POR2
BIAS
WDE
18
WDO
17
RST1
16
RST2
15 FB2
14 RUN/SS2
13 BST2
WDI
24 23 22 21 20 19
BST2 10
RUN/SS2 11
FB2 12
FE PACKAGE
24-LEAD PLASTIC TSSOP
θ
JA
= 38°C/W
EXPOSED PAD (PIN 25) IS GND, MUST BE ELECTRICALLY CONNECTED TO PCB
UF PACKAGE
24-LEAD (4mm
×
4mm) PLASTIC QFN
θ
JA
= 37°C/W
EXPOSED PAD (PIN 25) IS GND, MUST BE ELECTRICALLY CONNECTED TO PCB
ORDER INFORMATION
LEAD FREE FINISH
LT3688EFE#PBF
LT3688IFE#PBF
LT3688HFE#PBF
LT3688EUF#PBF
LT3688IUF#PBF
TAPE AND REEL
LT3688EFE#TRPBF
LT3688IFE#TRPBF
LT3688HFE#TRPBF
LT3688EUF#TRPBF
LT3688IUF#TRPBF
PART MARKING*
LT3688FE
LT3688FE
LT3688FE
3688
3688
PACKAGE DESCRIPTION
24-Lead Plastic TSSOP
24-Lead Plastic TSSOP
24-Lead Plastic TSSOP
24-Lead (4mm
×
4mm) Plastic QFN
24-Lead (4mm
×
4mm) Plastic QFN
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–40°C to 150°C
–40°C to 125°C
–40°C to 125°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/
3688f
2
LT3688
ELECTRICAL CHARACTERISTICS
SYMBOL
PARAMETER
V
IN
Undervoltage Lockout
Quiescent Current from V
IN
V
EN/UVLO
= 0.3V
V
BIAS
= 5V, Not Switching
V
BIAS
= 0V, Not Switching
V
EN/UVLO
= 0.3V
V
BIAS
= 5V, Not Switching
V
BIAS
= 0V, Not Switching
The
l
denotes the specifications which apply over the full operating
junction temperature range, otherwise specifications are at T
A
= 25°C. V
IN
= 12V, unless otherwise noted. (Note 3)
CONDITIONS
l
l
MIN
3
TYP
3.5
0.01
65
235
0.01
155
–5
MAX
3.8
1
105
310
1
200
–20
0.810
0.814
–50
2.35
540
180
2.2
–1
1.6
2
2.5
25
1.35
6
5.5
–4
1
1.3
92
25.8
22
1.6
0.4
0.3
30
1.3
UNITS
V
μA
μA
μA
μA
μA
μA
V
V
nA
%/V
MHz
kHz
ns
A
mV
μA
A
μA
V
mA
V
μA
μA
μA
μA
V
V
%
ms
ms
ms
ms
V
V
μs
V
μA
ns
Quiescent Current from BIAS
l
FB Voltage
FB Pin Bias Current
FB Voltage Line Regulation
Switching Frequency
Minimum Off-Time (Note 4)
Switch Current Limit (Note 5)
Switch V
CESAT
Switch Leakage Current (Note 8)
DA Current Limit
Boost Schottky Reverse Leakage
Minimum BST Voltage above SW
BST Pin Current
EN/UVLO Threshold Voltage
EN/UVLO Input Current
Threshold Current Hysteresis
RUN/SS Pin Current
RUN/SS Switching Threshold
SYNC Threshold Voltage
V
UV
t
RST
t
WDU
t
WDL
t
WDTO
Reset Threshold
Reset Timeout Period
Watchdog Window Upper Boundary
Watchdog Window Lower Boundary
Watchdog Timeout Period
RST
Output Voltage Low
t
UV
UV Detect to
RST
Asserted
WDI Input Threshold
WDI Input Pull-Up Current
WDI Input Pulse Width
WDE
Threshold Voltage
WDE
Input Pull-Down Current
WDO
Output Voltage Low
V
WDE
= 1.2V
I
SINK
= 2.5mA
I
SINK
= 100μA
% of FB Voltage, V
FB
Falling
C
POR
= 4700pF
C
WDT
= 1000pF
C
WDT
= 1000pF
C
WDT
= 1000pF
I
SINK
= 2.5mA, V
FB
= 0.6V
I
SINK
= 100μA, V
FB
= 0.6V
V
FB
Set to 0.680V
V
RUN/SS
= 0V
V
EN/UVLO
= 1.35V
V
EN/UVLO
= 1.15V
I
SW
= 0.8A
V
BIAS
= 0V
V
FB
= 0.800V
5V < V
IN
< 36V
R
T
= 20k, V
BST
= 12V
R
T
= 110k, V
BST
= 12V
V
BST
= 12V
DC = 15%
I
SW
= 0.8A
l
l
l
l
l
l
0.790
0.784
0.800
–3
0.002
1.85
460
1.2
2.1
500
115
1.7
280
–0.01
l
0.9
1.2
0.01
2.15
15
l
1.15
2.5
2.5
–1.4
0.15
0.4
1.25
0.3
4
3.7
–2.8
0.8
0.8
90
23.5
20
1.25
2.5
0.2
0.01
l
l
l
l
l
l
l
l
l
l
l
l
88
21.2
18
0.8
4
0.4
300
0.4
10
0.95
–2
0.65
3.5
0.2
0.01
1
0.4
0.3
V
μA
V
V
3688f
3
LT3688
ELECTRICAL CHARACTERISTICS
SYMBOL
PARAMETER
RST
Pull-Up Current (Note 6)
WDO
Pull-Up Current (Note 6)
CONFIG Low Level Input Voltage
CONFIG High Level Input Voltage
CONFIG Pin Voltage When Open
Maximum CONFIG Input Current in Open
State
CONFIG Pin Bias Current
V
CONFIG
= 0V, V
IN
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
Absolute Maximum Voltage at the V
IN
, CONFIG and EN/UVLO pins
is 36V for continuous operation.
Note 3:
The LT3688 is tested under pulsed load conditions such that
T
J
= T
A
. The LT3688E is guaranteed to meet performance specifications
from 0°C to 125°C junction temperature. Specifications over the –40°C
to 125°C operating junction temperature range are assured by design,
characterization and correlation with statistical process controls. The
LT3688I is guaranteed over the full –40°C to 125°C operating junction
temperature range. The LT3688H is guaranteed over the full –40°C to
150°C operating junction temperature range. High junction temperatures
degrade operating lifetimes. Operating lifetime is derated at junction
temperatures greater than 125°C. The junction temperature (T
J
, in °C) is
calculated from the ambient temperature (T
A
, in °C) and power dissipation
(PD, in Watts) according to the formula:
T
J
= T
A
+ (PD
θ
JA
), where
θ
JA
(in °C/W) is the package thermal
impedance.
l
l
l
l
The
l
denotes the specifications which apply over the full operating
junction temperature range, otherwise specifications are at T
A
= 25°C. V
IN
= 12V, unless otherwise noted. (Note 3)
CONDITIONS
MIN
–1.5
–1.5
1.4
0.64
±1
±20
TYP
–2.5
–2.5
0.2
MAX
UNITS
μA
μA
V
V
V
μA
μA
Note 4:
The LT3688 contains circuitry that extends the maximum duty
cycle if the BST voltage is 2V greater than the SW voltage. See the
Applications Information section for more details.
Note 5:
Current limit is guaranteed by design and/or correlation to static
test. Slope compensation reduces current limit at higher duty cycles.
Note 6:
The outputs of
RST
and
WDO
have a weak pull-up to V
BIAS
of
typically 2.5μA. However, external pull-up resistors may be used when
faster rise times are required or for V
OH
higher than V
BIAS
.
Note 7:
This IC includes overtemperature protection that is intended
to protect the device during momentary overload conditions. Junction
temperature will exceed the maximum operating junction temperature
when over-temperature protection is active. Continuous operation above
the specified maximum operating junction temperature may impair device
reliability.
Note 8:
All currents into pins are positive; all voltages are referenced to
I want to design a temperature record, please help me~ I'm here to make the following request: Detect temperature: Display temperature information on LCD. Record temperature: Press 0# key, LCD will di...
[i=s]This post was last edited by paulhyde on 2014-9-15 03:56[/i] When the contest questions came out, our teacher chose question H for us to do. Today, when we debugged it, the result was not very sa...
I want to read the voltage value on the VDD pin of 430. Does anyone have it? Can I refer to it? I want to read the voltage value on the VDD pin of 430 to roughly judge the remaining power of the 3.6V ...
Hardware designers have begun to adopt FPGA technology in high-performance DSP designs because it can provide 10-100 times faster computing than PC-based or microcontroller-based solutions. Previou...[Details]
When the WDP500-2A plane grating monochromator is used to test the emission wavelength of a high-power laser diode at different currents, the matching of the laser diode has the disadvantages of lo...[Details]
1 Introduction
With the acceleration of the pace of urban modernization, society has higher requirements for urban road lighting and urban lighting projects. The state has clearly required tha...[Details]
1. With the development of modern industry and the continuous improvement of automation, some medium and large control systems have been greatly facilitated, which not only makes control easier, bu...[Details]
This week, Microsoft held its 2012 Microsoft Worldwide Partner Conference (WPC) in Toronto, Canada. At the conference, Microsoft showed its new products and services to partners around the world. A...[Details]
0 Introduction
With the rise and continuous improvement of the solid-state lighting industry, light-emitting diodes (LEDs) have become an alternative lighting technology and are gr...[Details]
The potentiometer is an adjustable electronic component. The main functions of the potentiometer in the circuit are as follows:
1. Used as a voltage divider
A potentiometer is a continuou...[Details]
Among the many members of the single-chip microcomputer family, the MCS-51 series of single-chip microcomputers has occupied the main market of industrial measurement and control and automation eng...[Details]
From the previous section, we have learned that the timer/counter in the microcontroller can have multiple uses, so how can I make them work for the purpose I need? This requires setting the timer/...[Details]
Problems such as the depletion of natural resources, air pollution, traffic congestion, and rising fossil fuel prices have forced societies and individuals to seek alternative means of transportati...[Details]
Motors, especially those with brushes, generate a lot of noise. This noise must be dealt with if the appliance is to meet the requirements of EMC standards. The means to solve EMC are nothing more ...[Details]
1 Introduction
Ultrasound refers to elastic vibration with a frequency higher than the audible frequency limit (i.e., in the frequency band above 20 kHz). The propagation process of this vib...[Details]
Introduction
Today, as IC (integrated circuit) has developed to a super-large scale, IC design based on IP (Intellectual Property) cores and their reuse are important means to ensure the ef...[Details]
LED is the abbreviation of the English word. Its main meanings are: LED = Light Emitting Diode, a solid-state semiconductor device that can convert electrical energy into visible light. It can dire...[Details]
Zarlink Semiconductor has developed an ultra-low-power RF transceiver chip for pacemakers, neurostimulators, drug pumps, and other such implantable medical devices. It has high data rates, low power c...[Details]
Embedded System
京公网安备 11010802033920号
EEWORLD
