EXPOSED PAD (PIN 15) IS PGND, MUST BE SOLDERED TO PCB
MSE PACKAGE
16-LEAD PLASTIC MSOP
T
JMAX
= 150°C,
θ
JA
= 40°C/W,
θ
JC
= 10°C/W
EXPOSED PAD (PIN 17) IS PGND, MUST BE SOLDERED TO PCB
ORDER INFORMATION
LEAD FREE FINISH
LTC3111EDE#PBF
LTC3111IDE#PBF
LTC3111HDE#PBF
LTC3111MPDE#PBF
LTC3111EMSE#PBF
LTC3111IMSE#PBF
LTC3111HMSE#PBF
LTC3111MPMSE#PBF
TAPE AND REEL
LTC3111EDE#TRPBF
LTC3111IDE#TRPBF
LTC3111HDE#TRPBF
LTC3111MPDE#TRPBF
LTC3111EMSE#TRPBF
LTC3111IMSE#TRPBF
LTC3111HMSE#TRPBF
LTC3111MPMSE#TRPBF
PART MARKING*
3111
3111
3111
3111
3111
3111
3111
3111
PACKAGE DESCRIPTION
14-Lead (4mm
×
3mm) Plastic DFN
14-Lead (4mm
×
3mm) Plastic DFN
14-Lead (4mm
×
3mm) Plastic DFN
14-Lead (4mm
×
3mm) Plastic DFN
16-Lead Plastic MSOP
16-Lead Plastic MSOP
16-Lead Plastic MSOP
16-Lead Plastic MSOP
TEMPERATURE RANGE
–40°C to 125°C
–40°C to 125°C
–40°C to 150°C
–55°C to 150°C
–40°C to 125°C
–40°C to 125°C
–40°C to 150°C
–55°C to 150°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on nonstandard lead based finish parts.
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/
3111fa
2
For more information
www.linear.com/LTC3111
LTC3111
The
l
denotes the specifications which apply over the specified operating
junction temperature range, otherwise specifications are at T
A
= 25°C (Note 2). V
IN
= V
OUT
= PWM/SYNC = RUN = 5V unless otherwise
noted.
PARAMETER
Input Operating Range
V
IN
UVLO Threshold
V
IN
UVLO Hysteresis
V
CC
UVLO Threshold
V
CC
UVLO Hysteresis
Output Voltage Adjust Range
INTV
CC
Clamp Voltage
Quiescent Current—Burst Mode Operation
Quiescent Current—Shutdown
Feedback Voltage
Feedback Leakage
NMOS Switch Leakage
NMOS Switch On-Resistance
Input Current Limit
Peak Current Limit
Burst Current Limit
Burst Zero Current Threshold
Reverse Current Limit
Maximum Duty Cycle
Minimum Duty Cycle
SW1, SW2 Minimum Low Time
Frequency
SYNC Frequency Range
PWM/SYNC Threshold
RUN Threshold to Enable V
CC
RUN Threshold to Disable V
CC
RUN Threshold to Enable Switching
RUN Hysteresis
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetimes.
Note 2:
The LTC3111 is tested under pulsed load conditions such that
T
J
≈ T
A
. The LTC3111E is guaranteed to meet specifications from
0°C to 85°C junction temperature. Specifications over the –40°C to
125°C operating junction temperature range are assured by design,
characterization and correlation with statistical process controls. The
LTC3111I is guaranteed to meet performance specifications from –40°C
Rising
Falling
Rising
Percentage of the Period SW2 is Low in Boost Mode
(Note 7)
Percentage of the Period SW1 is Low in Buck Mode
(Note 7)
(Note 7)
PWM/SYNC = 5V
(Note 6)
l
l
l
l
l
l
l
l
l
ELECTRICAL CHARACTERISTICS
CONDITION
MIN
l
TYP
2.1
200
2.35
190
MAX
15
2.3
2.5
15
UNITS
V
V
mV
V
mV
V
V
µA
µA
V
nA
µA
mΩ
mΩ
2.5
1.9
2.2
2.5
3.9
4.2
55
0
Rising
Rising
l
l
V
IN
= 5V or 15V
FB = 1V, PWM/SYNC = 0V
RUN = V
OUT
= V
CC
= 0V, Not Including Switch Leakage
PWM Operation
FB = 0.8V
Switches A, B, C, D, V
IN
= V
OUT
= 15V
Switch A
Switch B, C, D
l
4.5
80
1
0.82
50
5
l
0.78
0.8
0
0.5
90
105
l
2.3
3
5.8
0.8
0.1
–1
3.7
A
A
A
A
A
%
PWM/SYNC = 0V
PWM/SYNC = 0V
85
90
0
160
%
ns
700
600
0.5
0.35
0.3
1.15
800
0.9
0.8
1.18
120
900
1500
1.5
1.15
1.23
kHz
kHz
V
V
V
V
mV
to 125°C junction temperature, the LTC3111H is guaranteed to meet
performance specifications from –40°C to 150°C junction temperature
and the LTC3111MP is guaranteed and tested to meet performance
specifications from –55°C to 150°C junction temperature. High junction
temperatures degrade operating lifetimes: operating lifetime is derated
for junction temperatures greater than 125°C. Note that the maximum
ambient temperature consistent with these specifications is determined by
specific operating conditions in conjunction with board layout, the rated
package thermal resistance and other environmental factors.
3111fa
For more information
www.linear.com/LTC3111
3
LTC3111
ELECTRICAL CHARACTERISTICS
Note 3:
This IC includes overtemperature protection that is intended
to protect the device during momentary overload conditions. Junction
temperatures will exceed 150°C when overtemperature protection is
active. Continuous operation above the specified maximum operating
junction temperature may impair device reliability.
Note 4:
Voltage transients on the switch pins beyond the DC limit specified
in the Absolute Maximum Ratings, are non-disruptive to normal operation
when using good layout practices, as shown on the demo board or
described in the data sheet and application notes.
Note 5:
The junction temperature (T
J
in °C) is calculated from the ambient
temperature (T
A
in °C) and power dissipation (P
D
in Watts) according to
the formula:
T
J
= T
A
+ (P
D
•
θ
JA
)
where
θ
JA
(in °C/W) is the package thermal impedance.
Note 6:
SYNC frequency range is tested with a square wave. Operation
with 100ns minimum high or low time is assured by design.
Note 7:
Switch timing measurements are made in an open-loop test
configuration. Timing in the application may vary somewhat from these
values due to differences in the switch pin voltage during the non-overlap
durations when the switch pin voltage is influenced by the magnitude and
Circuit Function and AdvantagesIn many process control applications, two-wire current transmitters are often used to transmit analog signals in a high noise environment. These current transmitters hav...
[size=5]When I use multiplexing functions, sometimes there are several multiplexed functions on the same pin[/size] [size=5] [/size] [size=5]For example, STM32F107's [color=#ff0000]PA2[/color][/size] ...
Now the target board I made has a JTAG interface. I use IAR software + JTAG programming and debugging. After debugging is normal, after removing the JTAG interface line, the target board can automatic...
There are many different ways of human-computer interaction. The more common ones are listed below:
Mouse interaction: Using a mouse to operate a computer and interact was the most common human...[Details]
Reflow soldering is a critical process in electronics assembly production, and the cleanliness of the reflow oven has a direct impact on product quality. Dust and residue accumulation within the ov...[Details]
Most of the houses we live in now are elevator buildings, mainly because it is more convenient to go up and down the stairs! It can also make life more comfortable. It even helps to increase the ad...[Details]
Long ago, the lifespan of cars in my country was 15 years. Once a car reached 15 years old, it was forced to be scrapped. However, the policy was later changed. As long as the car does not exceed 6...[Details]
In recent years, the government has increasingly supported electric vehicles, and the number of electric vehicles has increased. Observant drivers will notice that there are many more green license...[Details]
In recent years, with the application of the IEC61850 standard and the development and deployment of optoelectronic transformers, the concept of digital substations has been put into practical use ...[Details]
Today's security industry has entered the era of massive networking. Many enterprises, especially financial institutions, have established multi-level video surveillance networking platforms. Lever...[Details]
As time goes by, people are increasingly concerned about their own and their families' health. However, existing monitoring devices for individual vital signs have struggled to gain market share du...[Details]
The automotive industry in 2025 is undergoing a thorough intelligent reshuffle.
Geely wants to make changes in the field of AI cockpits: in the future, there will be no traditional smart...[Details]
On August 22, according to the Ministry of Industry and Information Technology's official website, my country's first mandatory national standard for the control of hazardous substances in electric...[Details]
As the scale and business applications of national e-government networks continue to expand, the data and services transmitted over them are becoming increasingly sensitive and critical. To protect...[Details]
Tires are a very important component for cars. They are related to the driving experience of the vehicle. We are almost inseparable from cars in our daily lives. For tires, according to the role of...[Details]
Normally, we determine our location and where we want to go by comparing our surroundings with observation and simple GPS tools. However, this kind of reasoning is very difficult for self-driving c...[Details]
1. Multi-channel DAC technology bottleneck
Currently,
the development of multi-channel DAC technology focuses on two core challenges.
First, industrial applications urgently ...[Details]
Through AI connection technology supported by Qualcomm X85 5G modem and RF and Qualcomm FastConnect 7900 mobile connection system, seamless switching can be achieved between cellular net...[Details]
ADI Reference Circuit
京公网安备 11010802033920号
EEWORLD
