to GND .................................................. –0.3V to 7V
SDAIN, SCLIN, SDAOUT, SCLOUT, READY, ENABLE,
FAULT, ACC .................................................. –0.3V to 7V
Operating Temperature
LTC4304C ................................................ 0°C to 70°C
LTC4304I .............................................–40°C to 85°C
PACKAGE/ORDER I FOR ATIO
TOP VIEW
ENABLE
SCLOUT
SCLIN
ACC
GND
1
2
3
4
5
11
10 V
CC
9 SDAOUT
8 SDAIN
7 FAULT
6 READY
DD PACKAGE
10-LEAD (3mm
×
3mm) PLASTIC DFN
T
JMAX
= 125°C,
θ
JA
= 43°C/W
EXPOSED PAD (PIN 11)
PCB GND CONNECTION OPTIONAL
ORDER PART NUMBER
LTC4304CDD
LTC4304IDD
DD PART MARKING*
LBBD
LBBD
Order Options
Tape and Reel: Add #TR
Lead Free: Add #PBF Lead Free Tape and Reel: Add #TRPBF
Lead Free Part Marking:
http://www.linear.com/leadfree/
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
ELECTRICAL CHARACTERISTICS
SYMBOL
Power Supply
V
CC
I
CC
Startup Circuitry
V
PRE
T
IDLE
V
OL_READY
V
THR_ENABLE
I
ENABLE
V
THR
PARAMETER
Positive Supply Voltage
Supply Current
Supply Current, ENABLE = GND
Precharge Voltage
Bus Idle Time
READY Output Low Voltage
The
●
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C. V
CC
= 2.7V to 5.5V, unless otherwise noted.
CONDITIONS
●
V
CC
= 5.5V, V
SDAIN
= V
SDAOUT
= 0V (Note 7)
V
CC
= 5.5V
SDA, SCL Floating, V
CC
= 5.5V
I
PULLUP
= 3mA
I
PULLUP
= 6mA, V
CC
= 4.7V
ENABLE Threshold
ENABLE Input Current
ENABLE from 0 to V
CC
SDA, SCL Logic Input Threshold Voltage Rising Edge
2
U
U
W
W W
U
W
TOP VIEW
ENABLE
SCLOUT
SCLIN
ACC
GND
1
2
3
4
5
10
9
8
7
6
V
CC
SDAOUT
SDAIN
FAULT
READY
MS10 PACKAGE
10-LEAD PLASTIC MSOP
T
JMAX
= 125°C,
θ
JA
=200°C/W
ORDER PART NUMBER
LTC4304CMS
LTC4304IMS
MS PART MARKING*
LTBBC
LTBBC
MIN
2.7
TYP
MAX
5.5
8
UNITS
V
mA
mA
V
µs
V
V
V
µA
V
4304fa
●
6
1.5
0.8
60
1
95
●
●
●
●
●
●
●
1.2
175
0.4
0.4
2
±1.5
2
0.8
1.6
1.4
0.1
1.8
LTC4304
ELECTRICAL CHARACTERISTICS
SYMBOL
V
HYS
t
PLH
t
PHL
I
OFF_READY
PARAMETER
The
●
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C. V
CC
= 2.7V to 5.5V, unless otherwise noted.
CONDITIONS
MIN
TYP
50
300
10
●
●
MAX
UNITS
mV
ns
ns
SDA, SCL, Logic Input Threshold Voltage (Note 6)
Hysteresis
ENABLE Delay On-Off
READY Delay Off-On
ENABLE Delay Off-On
READY Delay On-Off
V
CC
= 3.3V
(Note 6)
V
CC
= 3.3V
(Note 6)
60
95
10
175
±10
µs
ns
µA
mA
ns
V
V
µA
ms
V
µA
mV
mV
pF
V
µA
V
kHz
µs
ns
ns
ns
ns
ns
Ready Off Leakage Current
Rise-Time Accelerators
I
PULLUPAC
Transient Boosted Pull-Up Current
ACC Delay, On/Off
V
IH
Input High Voltage
Input Low Voltage
V
IL
I
IN
ACC Input Current
Bus Stuck Low Timeout
t
TIMEOUT
Bus Stuck Low Timer
V
OLFAULT
FAULT Output Low Voltage
I
OFF_FAULT
Input-Output Connection
V
OS
Input-Output Offset Voltage
t
PDOFF
Positive Transition on SDA, SCL, V
CC
= 2.7V,
Slew Rate = 0.8V/µs (Note 5)
(Note 6)
Measured on ACC
Measured on ACC
ACC Shorted to GND or V
CC
(Note 8)
SDAOUT, SCLOUT = 0V
I
PULLUP
= 3mA
V
CC
= 5.5V
10k to V
CC
on SDA, SCL,
2.7k to V
CC
on SDA, SCL
V
CC
= 3.3V, V
SDA/SCL
= 0.2V (Note 4)
(Note 6)
●
●
●
●
●
●
●
●
2
3.5
5
5.5
0.9V
CC
–100
25
30
0.1V
CC
100
35
0.4
±10
120
150
10
40
50
80
100
C
IN
V
IL, MAX
Digital Input Capacitance
SDAIN, SDAOUT, SCLIN, SCLOUT
Input Logic Low Voltage
I
LEAK
Input Leakage Current
V
OL
Output Low Voltage, Input = 0V
Timing Characteristics
f
I2C, MAX
I
2
C Maximum Operating Frequency
t
BUF
Bus Free Time Between Stop and Start
Condition
t
HD, STA
Hold Time After (Repeated)
Start Condition
t
SU, STA
Repeated Start Condition Set-Up Time
t
SU, STO
t
HD, DATI
t
SU, DAT
Stop Condition Set-Up Time
Data Hold Time Input
Data Set-Up Time
●
SDA, SCL, V
CC
= 5.5V
SDA, SCL Pins, I
SINK
= 4mA, V
CC
= 2.7V
(Note 6)
(Note 6)
(Note 6)
(Note 6)
(Note 6)
(Note 6)
(Note 6)
●
●
0
400
0.19
600
0.4
±5
0.3
1.3
100
0
0
0
100
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
All currents into pins are positive; all voltages are referenced to
GND unless otherwise specified.
Note 3:
Pulsed less than 5µs.
Note 4:
The connection circuitry always regulates the output to a higher
voltage than its input. The magnitude of this offset voltage as a function of
the pull-up resistor and V
CC
voltage is shown in the Typical Performance
Characteristics section.
Note 5:
I
PULLUPAC
varies with temperature and V
CC
voltage, as shown in
the Typical Performance Characteristics section.
Note 6:
Determined by design, not tested in production.
Note 7:
I
CC
test performed with connection circuitry active.
Note 8:
When floating, the ACC pin can tolerate ±5µA of leakage.
4304fa
3
LTC4304
TYPICAL PERFOR A CE CHARACTERISTICS
I
CC
vs Temperature
6.2
6.0
5.8
t
PHL
(ns)
I
CC
(mA)
80
60
40
V
CC
= 2.7V
20
0
–50
2
0
–50
5.6
5.4
5.2
5.0
–50
V
CC
= 5.5V
140
120
100
I
PULLUPAC
(mA)
–25
0
25
50
TEMPERATURE (°C)
Connection Circuitry V
OUT
- V
IN
250
180
200
V
CC
= 5.5V
V
OUT
-V
IN
(mV)
t
PHL
(ns)
150
140
120
100
80
60
50
40
0
1000
20
3000
7000
5000
R
PULLUP
(Ω)
9000
4303 G04
100
V
CC
= 2.7V
4
U W
75
100
4303 G01
T
A
= 25°C unless otherwise indicated.
I
PULLUPAC
vs Temperature
14
12
10
8
6
4
V
CC
= 2.7V
V
CC
= 3.3V
V
CC
= 5.5V
Input-Output t
PHL
vs Temperature
C
IN
= C
OUT
= 100pF
R
PULLUPIN
= R
PULLUPOUT
= 10k
–25
0
25
50
TEMPERATURE (°C)
75
100
4303 G02
–25
0
25
50
TEMPERATURE (°C)
75
100
4303 G03
Input-Output t
PHL
vs C
OUT
C
IN
= 50pF
R
PULLUPIN
= R
PULLUPOUT
= 10k
160
0
500
1000
C
OUT
(pF)
1500
2000
4303 G05
4304fa
LTC4304
PI FU CTIO S
ENABLE (Pin 1):
Connection Enable. This is a digital
threshold input pin. For normal operation ENABLE is high.
Driving ENABLE below 0.8V isolates SDAIN from SDAOUT,
SCLIN from SCLOUT, asserts READY low and disables
automatic clocking. A rising edge on ENABLE after a fault
has occurred unconditionally forces a connection between
SDAIN, SDAOUT and SCLIN, SCLOUT.
SCLOUT (Pin 2):
Serial Clock Output. Connect this pin to
the SCL bus on the card.
SCLIN (Pin 3):
Serial Clock Input. Connect this pin to SCL
on the bus backplane.
ACC (Pin 4):
Rise-Time Accelerator Control. Connect ACC
to V
CC
to disable all four accelerators. Connect ACC to
GND to enable all four accelerators. Float ACC to enable
the SDAOUT and SCLOUT accelerators only. For applica-
tions when V
CC
is greater than the bus pull-up voltage,
connect ACC to V
CC
.
GND (Pin 5):
Device Ground. Connect this pin to a ground
plane for best results.
READY (Pin 6):
Connection Status Flag. READY provides
a digital flag which indicates the status of the connection
circuitry described in the “Connection Circuitry” section.
Connect a resistor of 10k to V
CC
to provide the pull-up.
FAULT (Pin 7):
Bus Stuck Low Fault. FAULT is an open
drain N-channel MOSFET which pulls low to signal a bus
stuck low condition. In normal operation, FAULT is high.
Design of Touch-type MP3 Player Based on DSP This paper introduces the design of a touch-type MP3 player using the digital signal processing chip TMS320LF2407A. The chip VS1003B is used to decode MP3...
The board has arrived. At the request of the group management, I still want to show it off. I still share two activity links: https://www.eeworld.com.cn/huodong/TI_MSP430Workshop_20200602/?from=groupm...
For some reason, the pointer in the PCB interface has a square. When only the top layer is displayed, you can see the bottom layer through this square, giving you a sense of perspective.What is it and...
Congratulations to Zhixin Technology for receiving 5 million angel investment. Now Zhixin Technology has decided that all students who come to Beijing Zhixin for training on July 23 can only charge 6,...
I would like to ask all the experts, how to convert the 3.3V square wave output by DSP into 12VI want a 12V square wave with variable frequency from 50Hz to 10MHz.Can any expert give me some advice on...
Eight characteristics of the top 100 electronics companies in the past 20 years2006-6-2 Ministry of Information Industry Since 1987, the ranking of China's top 100 electronic information companies ha...
The radio frequency identification (RFID) market is experiencing strong growth, with sales reaching $1.7 billion in 2004 and expected to reach $5.9 billion in 2008. This surge in demand is driven b...[Details]
Medicines are special commodities. If patients are given the wrong medicine, fake medicine, inferior medicine or expired medicine, it will pose a threat to people's health and lives.
In recent...[Details]
Many medical applications require portable, self-powered devices that do not require external power and data cables. The most obvious example is a portable data logger that patients carry with them to...[Details]
Maximize instrument utilization and reduce
test times
Increasing the throughput of automated test systems can improve efficiency. Using off-the-shelf tools (COTS) such as multicore proc...[Details]
introduction
Video surveillance systems are widely used in industrial, military and civil fields, playing an important role in the security and environmental monitoring of these industries...[Details]
Volkswagen's electronic throttle has taken our understanding of the traditional throttle a big step forward. However, while we admire Volkswagen's new technology, which is constantly being applied...[Details]
Preface
In recent years, many compact portable electronic products have been developed, such as mobile phones, digital cameras, MP3, MP4, PDA, GPS and DVD, etc. They are not only small in size...[Details]
With the rapid development of my country's power industry, the power system has higher requirements for the collection of power generation, transmission, distribution and consumption. As a prerequis...[Details]
Mesh network architecture and advantages
The Internet is a flat network. The routers that make up the Internet are on the same plane. The mesh network formed by multiple paths between ...[Details]
From a broad perspective, the development of digital television in my country started in 1995 with a special project on digital television science and technology. In 1998, China's first and the wo...[Details]
With the continuous development of digital television, the demand for high-definition is imperative. H.264, as a new generation of compression standard, has a more complete algorithm than MPEG-2, ...[Details]
0 Introduction
Electric vehicles are high-tech products that integrate computer technology, communication technology, electronic technology, and new material technology. They have a complex ...[Details]
Femtocell base stations are required to meet stringent requirements in terms of interference, compatibility testing between mobile devices and networks (such as ad hoc networks, handovers), and mee...[Details]
The car sensor simulation tester simulates the input signal of the car computer and replaces the sensor. It does not need to replace the sensor, so it can accurately judge the quality of the sensor...[Details]
1 Introduction
Motion controllers are core motion control components commonly used in mechatronic equipment such as CNC machine tools and robots. Modern CNC technology has put forward higher a...[Details]
DSP and ARM Processors
京公网安备 11010802033920号
EEWORLD
