EXPOSED PAD (PIN 9) CONNECTION TO GROUND IS OPTIONAL
MS8 PACKAGE
8-LEAD PLASTIC MSOP
T
JMAX
= 125°C,
θ
JA
= 200°C/W
ORDER INFORMATION
LEAD FREE FINISH
LTC4308CDD#PBF
LTC4308IDD#PBF
LTC4308CMS8#PBF
LTC4308IMS8#PBF
TAPE AND REEL
LTC4308CDD#TRPBF
LTC4308IDD#TRPBF
LTC4308CMS8#TRPBF
LTC4308IMS8#TRPBF
PART MARKING*
LBTT
LBTT
LTBTS
LTBTS
PACKAGE DESCRIPTION
8-Lead (3mm
×
3mm) Plastic DFN
8-Lead (3mm
×
3mm) Plastic DFN
8-Lead Plastic MSOP
8-Lead Plastic MSOP
TEMPERATURE RANGE
0°C to 70°C
–40°C to 85°C
0°C to 70°C
–40°C to 85°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *Temperature grades are identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C. V
CC
= 3.3V, unless otherwise noted.
SYMBOL
Power Supply
V
CC
I
CC
I
SD
V
PRE
Positive Supply Voltage
Supply Current
Shutdown Supply Current
Precharge Voltage
V
CC
= 5.5V, V
SCLOUT
= V
SDAOUT
= 0V (Note 6)
V
CC
= 5.5V, ENABLE = 0V
SDAOUT, SCLOUT Open
l
l
l
l
ELECTRICAL CHARACTERISTICS
PARAMETER
CONDITIONS
MIN
2.3
TYP
MAX
5.5
UNITS
V
mA
μA
V
4308f
7
900
0.8
1
11
1400
1.2
2
LTC4308
ELECTRICAL CHARACTERISTICS
SYMBOL
t
IDLE
V
THR_EN
V
THR_EN(HYST)
I
ENABLE
t
PLH_EN
t
PHL_EN
t
PLH_READY
t
PHL_READY
V
OL_READY
I
OFF_READY
t
PHL
t
PLH
t
RISE
t
FALL
I
PULLUPAC
PARAMETER
Bus Idle Time
ENABLE Threshold Voltage
ENABLE Threshold Voltage Hysteresis
ENABLE Input Current
ENABLE Delay Off-On
ENABLE Delay On-Off
READY Delay Off-On
READY Delay On-Off
READY Output Low Voltage
READY Off Leakage Current
SDA/SCL Propagation Delay High to Low
SDA/SCL Propagation Delay Low to High
SDA/SCL Transition Time Low to High
SDA/SCL Transition Time High to Low
Transient Boosted Pull-Up Current
ENABLE Rising Edge
(Note 3)
ENABLE from 0V to V
CC
(Figure 1)
(Note 3), (Figure 1)
(Note 3), (Figure 1)
(Note 3), (Figure 1)
I
READY
= 3mA, V
CC
= 2.3V
V
CC
= READY = 5.5V
C
LOAD
= 50pF 2.7k to V
CC
on SDA, SCL,
,
(Notes 2, 3), (Figure 1)
C
LOAD
= 50pF 2.7k to V
CC
on SDA, SCL,
,
(Notes 2, 3), (Figure 1)
C
LOAD
= 100pF 10k to V
CC
on SDA, SCL,
,
(Notes 3, 4), (Figure 1)
C
LOAD
= 100pF 10k to V
CC
on SDA, SCL,
,
(Notes 3, 4), (Figure 1)
Positive Transition > 0.8V/μs on SDAOUT,
SCLOUT (Note 5)
2.7k to V
CC
on SDAOUT, SCLOUT,
SDAIN = SCLIN = 0.2V
2.7k to V
CC
on SDAOUT, SCLOUT,
SDAIN = SCLIN = 0.4V, V
CC
= 5.5V
Output to Input Offset Voltage (IN – OUT)
2.7k to V
CC
on SDAIN, SCLIN,
SDAOUT = SCLOUT = 0.4V
2.7k to V
CC
on SDAIN, SCLIN,
SDAOUT = SCLOUT = 0.4V, V
CC
= 5.5V
V
THR
SDAOUT, SCLOUT Logic Input Threshold Voltage V
CC
≥ 2.9V
V
CC
< 2.9V
SDAIN, SCLIN Logic Input Threshold Voltage
V
THR(HYST)
SDAIN, SCLIN Rising Edge, V
CC
= 2.3V, 5.5V
SDAOUT, SCLOUT Logic Input Threshold Voltage (Note 3)
Hysteresis
SDAIN, SCLIN Logic Input Threshold Voltage
Hysteresis
C
IN
I
LEAK
V
OL
Digital Input Capacitance SDAIN, SDAOUT,
SCLIN, SCLOUT
Input Leakage Current
Output Low Voltage
(Note 3)
(Note 3)
SDA, SCL Pins
SDAOUT, SCLOUT Pins, I
SINK
= 4mA,
SDAIN = SCLIN = 0V, V
CC
= 2.7V
2.7k to V
CC
on SDAOUT, SCLOUT,
SDAIN = SCLIN = 0V
V
ILMAX
Buffer Input Logic Low Voltage
SDAOUT, SCLOUT Pins
l
l
l
l
l
l
l
l
l
l
l
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C. V
CC
= 3.3V, unless otherwise noted.
CONDITIONS
l
l
MIN
55
0.45
TYP
95
0.6
35
0.1
95
10
10
10
MAX
175
0.75
±5
UNITS
μs
V
mV
μA
μs
ns
ns
ns
0.4
0.1
70
10
30
30
5
8
300
300
±5
V
μA
ns
ns
ns
ns
mA
Prop Delay and Rise-Time Accelerators
Input-Output Connection
V
OS
Input to Output Offset Voltage (OUT – IN)
250
250
–150
–150
1.4
1.1
0.45
300
350
–200
–250
1.65
1.35
0.6
50
35
10
±5
0
250
300
400
380
1.2
380
450
–300
–350
1.9
1.6
0.75
mV
mV
mV
mV
V
V
V
mV
mV
pF
μA
mV
mV
V
4308f
3
LTC4308
ELECTRICAL CHARACTERISTICS
SYMBOL
t
TIMEOUT
f
I2C,MAX
t
BUF
t
HD,STA
t
SU,STA
t
SU,STO
t
HD,DATI
t
SU,DAT
PARAMETER
Bus Stuck Low Timer
I
2
C Maximum Operating Frequency
Hold Time After (Repeated) Start Condition
Repeated Start Condition Set-Up Time
Stop Condition Set-Up Time
Data Hold Time Input
Data Set-Up Time
Bus Stuck Low Timeout
SDAOUT = SCLOUT = 0V
(Note 3)
(Note 3)
(Note 3)
(Note 3)
(Note 3)
(Note 3)
l
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C. V
CC
= 3.3V, unless otherwise noted.
CONDITIONS
MIN
25
400
TYP
30
600
1.3
100
0
0
0
100
MAX
35
UNITS
ms
kHz
μs
ns
ns
ns
ns
ns
Timing Characteristics
Bus Free Time Between Stop and Start Condition (Note 3)
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
See “Propagation Delays” in the Operations section for a
discussion of t
PHL
and t
PLH
as a function of pull-up resistance and bus
capacitance.
Note 3:
Determined by design, not tested in production.
Note 4:
Measure points are 0.3 • V
CC
and 0.7 • V
CC
.
Note 5:
I
PULLUPAC
varies with temperature and V
CC
voltage as shown in the
Typical Performance Characteristics section.
Note 6:
I
CC
test performed with connection circuitry active.
Note 7:
All currents into pins are positive; all voltages are referenced to
GND unless otherwise specified.
TIMING DIAGRAMS
ENABLE, CONNECT, READY Timing
t
PLH_READY
t
PLH_EN
ENABLE
t
PHL_READY
t
PHL_EN
CONNECT
READY
4308 TD01
Rising and Falling Propagation Delays and Rise and Fall Times for SDAIN, SDAOUT and SCLIN, SCLOUT
It was originally a good 51 board, but the CPU socket was loose. I asked a colleague to tighten it, but when I brought it back, it suddenly did not work. It also did not work on the emulator. The scre...
Wow, my computer screen has become invisible and transparent. How...how...is this possible? Stay calm, this is not a supernatural event. The secret lies in the wallpaper...If you are tired of using re...
I need help from all the experts. I need to transplant MLO and uboot in ti sdk to our own board. There are some differences in hardware between our own board and the official development board. For ex...
Brief introduction of STM8S003K3T6C related knowledge: Standard packaging 250 Packaging Pallet Category Integrated Circuit (IC) Product Family Embedded - Microcontroller Series STM8S Other Names 497-1...
With the promotion of the construction of intelligent communities in the country, anti-theft systems have become essential equipment for intelligent communities. Especially in recent years, the urg...[Details]
China's new energy vehicles are in a transition period from research and development to real industrial development. In 2012, with the intensive launch of new energy vehicle policy planning, the de...[Details]
Due to the significant increase in electronic devices in automotive and industrial applications, the automotive and industrial markets continue to play an important role in China's electronics in...[Details]
With the advocacy and implementation of the government's Safe City Plan, the security market has increasingly higher requirements for the clarity of surveillance images. Imagine that after a case o...[Details]
Problems such as the depletion of natural resources, air pollution, traffic congestion, and rising fossil fuel prices have forced societies and individuals to seek alternative means of transportati...[Details]
We know that the inverter consists of two parts: the main circuit and the control circuit. Due to the nonlinearity of the main circuit (switching action), the inverter itself is a source of harmoni...[Details]
Motors, especially those with brushes, generate a lot of noise. This noise must be dealt with if the appliance is to meet the requirements of EMC standards. The means to solve EMC are nothing more ...[Details]
LED lighting: Basic circuit design can be completed in as little as one day
Semiconductor manufacturers are also getting involved in the LED lighting business. The power circuit of LED req...[Details]
The ARINC429 bus is one of the most commonly used communication buses between various subsystems of avionics. As the "skeleton" of modern avionics systems, once the bus system or the attached airbo...[Details]
LED is the abbreviation of the English word. Its main meanings are: LED = Light Emitting Diode, a solid-state semiconductor device that can convert electrical energy into visible light. It can dire...[Details]
The overall operating performance of an electric car depends first on its battery system and motor drive system. The drive system of an electric car is generally composed of three main parts: a con...[Details]
Introduction
my country's rapid economic growth is mainly due to the development of manufacturing and the acceleration of urbanization. However, urbanization cannot be achieved at the expense ...[Details]
1 Introduction
Lijia'an Yellow River Diversion Culvert is a large gravity diversion gate in the lower reaches of the Yellow River. The Yellow River Diversion Culvert is located in Lijia'an Vi...[Details]
The circuit has overcharge protection, over-discharge protection, over-current protection and short-circuit protection functions. Its working principle is analyzed as follows:
1 Normal state
...[Details]
1. Basic principles of organic/polymer solar cells
The basic principle of organic/polymer solar cells is to use the photovoltaic effect generated by light incident on the heterojunction of sem...[Details]
51mcu
京公网安备 11010802033920号
EEWORLD
