LTC4309C ................................................ 0°C to 70°C
LTC4309I.............................................. –40°C to 85°C
Storage Temperature Range (DE)........... –65°C to 125°C
Storage Temperature Range (GN) .......... –65°C to 150°C
Lead Temperature (Soldering, 10 sec)
GN Package ...................................................... 300°C
PIN CONFIGURATION
TOP VIEW
ENABLE
DISCEN
SCLOUT
SCLIN
ACC
GND
1
2
3
4
5
6
13
12 V
CC
11 V
CC2
10 SDAOUT
9
8
7
SDAIN
FAULT
READY
ENABLE
NC
DISCEN
SCLOUT
SCLIN
ACC
NC
GND
1
2
3
4
5
6
7
8
TOP VIEW
16 V
CC
15 NC
14 V
CC2
13 SDAOUT
12 SDAIN
11 FAULT
10 NC
9
READY
DE12 PACKAGE
12-LEAD (4mm
×
3mm) PLASTIC DFN
T
JMAX
= 125°C,
θ
JA
= 43°C/W
EXPOSED PAD (PIN 13) PCB CONNECTION TO GND IS OPTIONAL
GN PACKAGE
16-LEAD NARROW PLASTIC SSOP
T
JMAX
= 150°C,
θ
JA
= 110°C/W
ORDER INFORMATION
LEAD FREE FINISH
LTC4309CDE#PBF
LTC4309IDE#PBF
LTC4309CGN#PBF
LTC4309IGN#PBF
TAPE AND REEL
LTC4309CDE#TRPBF
LTC4309IDE#TRPBF
LTC4309CGN#TRPBF
LTC4309IGN#TRPBF
PART MARKING*
4309
4309
4309
4309I
PACKAGE DESCRIPTION
12-Lead (4mm
×
3mm) Plastic DFN
12-Lead (4mm
×
3mm) Plastic DFN
16-Lead Plastic SSOP
16-Lead Plastic SSOP
TEMPERATURE RANGE
0°C to 70°C
–40°C to 85°C
0°C to 70°C
–40°C to 85°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
Consult LTC Marketing for information on non-standard lead based finish parts.
For more information on lead free part marking, go to:
http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to:
http://www.linear.com/tapeandreel/
4309fa
2
LTC4309
ELECTRICAL CHARACTERISTICS
SYMBOL
V
CC
V
CC2
I
CC
I
SD
I
CC2
I
SD2
t
PHL
t
PLH
t
RISE
t
FALL
I
PULLUPAC
V
PRE
t
IDLE
V
THR_EN
V
THR_CTRL
I
CTRL
t
PLH_EN
t
PHL_EN
t
PLH_READY
t
PHL_READY
V
OL_READY
I
OFF_READY
f
I2C, MAX
t
BUF
t
HD, STA
t
SU, STA
t
SU, STO
t
HD, DATI
t
SU, DAT
V
OS
V
THR
PARAMETER
Positive Supply Voltage
Input Side Accelerator Supply Voltage
V
CC
Input Supply Current Enabled
V
CC
Input Supply Current Disabled
V
CC2
Input Supply Current Enabled
V
CC2
Input Supply Current Disabled
SDA/SCL Propagation Delay High to Low
SDA/SCL Propagation Delay Low to High
SDA/SCL Rise Time
SDA/SCL Fall Time
Transient Boosted Pull-up Current
Precharge Voltage
Bus Idle Time
ENABLE Threshold Voltage
ACC,
DISCEN Threshold Voltage
ENABLE,
ACC,
DISCEN Input Currents
ENABLE Delay Off-On
ENABLE Delay On-Off
READY Delay On-Off
READY Delay Off-On
READY Output Low Voltage
READY Off Leakage Current
I
2
C Maximum Operating Frequency
Bus Free Time Between Stop and Start
Condition
Hold Time After (Repeated)
Start Condition
Repeated Start Condition Set-Up Time
Stop Condition Set-Up Time
Data Hold Time Input
Data Set-Up Time
Input-Output Offset Voltage
SDA, SCL Logic Input Threshold Voltage
ENABLE,
ACC,
DISCEN from 0 to V
CC
(Figure 1)
(Note 3), (Figure 1)
(Note 3), (Figure 1)
(Note 3), (Figure 1)
I
READY
= 3mA, V
CC
= 2.3V
V
CC
= READY = 5.5V
(Note 3)
(Note 3)
(Note 3)
(Note 3)
(Note 3)
(Note 3)
(Note 3)
2.7k to V
CC2
on SDA, SCL, Driven SDA, SCL = 0.2V
V
CC
≥ 2.9V
V
CC
< 2.9V
l
l
l
l
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C. V
CC
= 3.3V, V
CC2
= 3.3V, unless otherwise noted.
CONDITIONS
l
l
l
l
l
l
MIN TYP MAX UNITS
2.3
1.8
7
190
140
85
10
30
30
5
l
l
l
5.5
5.5
11
250
180
900 1400
V
V
mA
μA
μA
μA
ns
ns
V
CC
= V
CC2
= 5.5V, V
SDAIN
= V
SCLIN
= 0V (Note 2)
V
CC
= V
CC2
= 5.5V, SDA = SCL = 5.5V, ENABLE = OV
V
CC
= V
CC2
= 5.5V, V
SDAIN
= V
SCLIN
= 0V (Note 2)
V
CC
= V
CC2
= 5.5V, SDA = SCL = 5.5V, ENABLE = OV
C
LOAD
= 50pF 2.7k to V
CC
on SDA, SCL, (Note 3, 4), (Figure 1)
,
C
LOAD
= 50pF 2.7k to V
CC
on SDA, SCL, (Note 3, 4), (Figure 1)
,
C
LOAD
= 100pF 10k to V
CC
on SDA, SCL, V
CC
= 5V V
CC2
= 5V,
,
(Note 3, 5), (Figure 1)
C
LOAD
= 100pF 10k to V
CC
on SDA, SCL, V
CC
= 5V (Note 3, 5),
,
(Figure 1)
Positive Transition > 0.8V/μS on SDA, SCL, V
CC
= 3.3V (Note 7)
SDA, SCL Open
ENABLE Rising Edge
(Note 3)
Propagation Delay and Rise Time Accelerators
300
300
ns
ns
mA
8
1.0
95
1.4
100
0.7
0.1
95
10
10
10
0.4
0.1
±5
1.2
175
2
1
±5
Start-Up Circuitry
0.8
55
0.8
0.5
V
μs
V
mV
V
μA
μs
ns
ns
ns
V
μA
kHz
1.3
100
0
0
0
100
20
1.4
1.1
60
1.65
1.35
100
1.9
1.6
μs
ns
ns
ns
ns
ns
mV
V
V
V
THR_EN(HYST)
ENABLE Threshold Voltage Hysteresis
Timing Characteristics
400
600
Input-Output Connection
4309fa
3
LTC4309
ELECTRICAL CHARACTERISTICS
SYMBOL
V
THR(HYST)
C
IN
I
LEAK
V
OL
PARAMETER
SDA, SCL Logic Input Threshold Voltage
Hysteresis
Digital Input Capacitance SDAIN,
SDAOUT, SCLIN, SCLOUT
Input Leakage Current
Output Low Voltage
The
l
denotes the specifications which apply over the full operating
temperature range, otherwise specifications are at T
A
= 25°C. V
CC
= 3.3V, V
CC2
= 3.3V, unless otherwise noted.
CONDITIONS
(Note 3)
(Note 3)
SDA, SCL,
ACC,
DISCEN Pins
SDA, SCL Pins, I
SINK
= 4mA, Driven SDA/SCL = 0.2V, V
CC
=
V
CC2
= 2.7V
2.7k to V
CC
on SDA, SCL, Driven SDA/SCL = 0.1V,
V
CC
= V
CC2
= 3.3V
l
l
l
l
l
l
l
MIN TYP MAX UNITS
50
10
±5
0
120
170
0.4
205
1.2
25
30
0.1
35
0.4
±5
mV
pF
μA
V
mV
V
ms
V
μA
V
ILMAX
t
TIMEOUT
V
OL_FAULT
I
OFF_FAULT
Buffer Input Logic Low Voltage
Bus Stuck Low Timer
FAULT
Output Low Voltage
FAULT
Off Leakage Current
SDAOUT, SCLOUT = OV
I
FAULT
= 3mA
Bus Stuck Low Timeout
Note 1:
Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2:
Test performed with connection circuity active.
Note 3:
Determined by design, not subject to test.
Note 4:
For larger equivalent bus capacitance, the skew increases, and
setup and hold times must be adjusted accordingly. Please see the
Operation Section of the datasheet.
Note 5:
Measure points are 0.3 • V
CC
and 0.7 • V
CC
.
Note 6:
All currents into pins are positive, all voltages are referenced to
The following content comes from the Zhihu topic [b][color=rgb(34, 85, 153)][url=https://www.zhihu.com/question/36391193]What inventions in history have deviated from the original intentions of the in...
st link unity has not been able to connect before, click connect and it shows Unknown device ID! Because the installation package was downloaded from a non-official channel before, and then I went to ...
Please recommend some popular science books about the development process of communication technology, especially books or web pages that explain signal modulation in an analog way. Web information is...
[code]//******************************************************************************** // Serial communication//Environment: C8051F120 // //Description: // // This program implements serial port pri...
From being a global leader to losing the market, Korean battery manufacturers have always wanted to regain the lost market and dignity, but facing Chinese battery manufacturers represented by CAT...[Details]
To understand why car engines need gearboxes, we must first understand the characteristics of different types of engines. An engine refers to a machine that can convert a form of energy into kineti...[Details]
"Have you set your calendar reminder?"
On August 24, Nvidia Robotics' official account posted a photo of a black gift box on a social media platform, with an attached greeting card sig...[Details]
As time goes by, people are increasingly concerned about their own and their families' health. However, existing monitoring devices for individual vital signs have struggled to gain market share du...[Details]
On August 22, the National Energy Administration released the latest data, showing that by the end of July 2025, China's total number of electric vehicle charging infrastructure will reach 16.696 m...[Details]
Have you ever heard stories about "crazy appliances"? Think of microwaves that turn on automatically or ovens that preheat without any human input? With radios and electromagnetic interfaces ubiqui...[Details]
Teletrac Navman has launched the Multi IQ dashcam, a cloud-based solution designed for large commercial vehicle operators. It connects up to five cameras to cover the vehicle's interior, sides, and...[Details]
With the gradual popularization of new energy vehicles in recent years, more and more people have been able to access and purchase electric vehicles. The structure of electric vehicles is composed ...[Details]
Cadence and NVIDIA Collaborate to Revolutionize Power Analysis Technology, Accelerating Development of Billion-Gate AI Designs
Cadence's new Palladium Dynamic Power Analysis applicat...[Details]
Introduction: Traditionally, lead-acid batteries have primarily been used to provide backup power and power regulation based on location. In typical applications, the battery's actual use (discharg...[Details]
Reasons for the wear of the roller press reducer shaft:
1. Since the expansion sleeve is subjected to a large torque, the mating surfaces of the shaft and the sleeve move relative to each other...[Details]
Electronics engineers all know that transient voltage suppression (TVS) diodes are used to protect ports, preventing damage to downstream circuits caused by transient voltage surges. In short, TVS ...[Details]
This series of articles aims to help readers have a brief understanding of the Hongke KPA Automation system and to quickly get started with MoDK, including: an introduction to Hongke KPA Automation...[Details]
A Beijing chemical project utilizes a distributed control system (DCS). The master control system primarily uses the Modbus protocol, while the remote field devices utilize the PROFIBUS-DP protocol...[Details]
Since entering the electronic components industry, I've learned that electronic components come in different packaging types. Some people have argued that different types of components may look the...[Details]
PCB Design
京公网安备 11010802033920号
EEWORLD
