PCA9539; PCA9539R
16-bit I
2
C-bus and SMBus low power I/O port with interrupt
and reset
Rev. 05 — 28 July 2008
Product data sheet
1. General description
The PCA9539; PCA9539R is a 24-pin CMOS device that provides 16 bits of General
Purpose parallel Input/Output (GPIO) expansion with interrupt and reset for
I
2
C-bus/SMBus applications and was developed to enhance the NXP Semiconductors
family of I
2
C-bus I/O expanders. I/O expanders provide a simple solution when additional
I/O is needed for ACPI power switches, sensors, push buttons, LEDs, fans, etc.
The PCA9539; PCA9539R consists of two 8-bit configuration (input or output selection),
input, output and polarity inversion (active HIGH or active LOW operation) registers. The
system master can enable the I/Os as either inputs or outputs by writing to the I/O
configuration bits. The data for each input or output is kept in the corresponding Input or
Output register. The polarity of the read register can be inverted with the Polarity inversion
register. All registers can be read by the system master.
The PCA9539; PCA9539R is identical to the PCA9555 except for the removal of the
internal I/O pull-up resistor which greatly reduces power consumption when the I/Os are
held LOW, replacement of A2 with RESET and a different address range.
The PCA9539; PCA9539R open-drain interrupt output is activated when any input state
differs from its corresponding input port register state and is used to indicate to the system
master that an input state has changed.
The power-on reset sets the registers to their default values and initializes the device state
machine. In the PCA9539, the RESET pin causes the same reset/default I/O input
configuration to occur without de-powering the device, holding the registers and I
2
C-bus
state machine in their default state until the RESET input is once again HIGH. This input
requires a pull-up to V
DD
. In the PCA9539R however, only the device state machine is
initialized by the RESET pin and the internal general-purpose registers remain
unchanged. Using the PCA9539R RESET pin will only reset the I
2
C-bus interface should
it be stuck LOW to regain access to the I
2
C-bus. This allows the I/O pins to retain their last
configured state so that they can keep any lines in their previously defined state and not
cause system errors while the I
2
C-bus is being restored.
Two hardware pins (A0, A1) vary the fixed I
2
C-bus address and allow up to four devices to
share the same I
2
C-bus/SMBus.
2. Features
I
I
I
I
16-bit I
2
C-bus GPIO with interrupt and reset
Operating power supply voltage range of 2.3 V to 5.5 V
5 V tolerant I/Os
Polarity inversion register
NXP Semiconductors
PCA9539; PCA9539R
16-bit I
2
C-bus and SMBus low power I/O port with interrupt and reset
I
I
I
I
I
I
I
I
I
Active LOW interrupt output
Active LOW reset input
Low standby current
Noise filter on SCL/SDA inputs
No glitch on power-up
Internal power-on reset
16 I/O pins which default to 16 inputs
0 Hz to 400 kHz clock frequency
ESD protection exceeds 2000 V HBM per JESD22-A114, 200 V MM per
JESD22-A115, and 1000 V CDM per JESD22-C101
I
Latch-up testing is done to JEDEC Standard JESD78 which exceeds 100 mA
I
Offered in three different packages: SO24, TSSOP24, and HVQFN24
3. Ordering information
Table 1.
Ordering information
Package
Name
PCA9539D
PCA9539PW
PCA9539RPW
PCA9539BS
PCA9539RBS
HVQFN24
plastic thermal enhanced very thin quad flat package; no leads;
24 terminals; body 4
×
4
×
0.85 mm
SOT616-1
SO24
TSSOP24
Description
plastic small outline package; 24 leads; body width 7.5 mm
plastic thin shrink small outline package; 24 leads; body width 4.4 mm
Version
SOT137-1
SOT355-1
Type number
3.1 Ordering options
Table 2.
PCA9539D
PCA9539PW
PCA9539RPW
PCA9539BS
PCA9539RBS
Ordering options
Topside mark
PCA9539D
PCA9539PW
PA9539RPW
9539
539R
Temperature range
−40 °C
to +85
°C
−40 °C
to +85
°C
−40 °C
to +85
°C
−40 °C
to +85
°C
−40 °C
to +85
°C
Type number
PCA9539_PCA9539R_5
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 05 — 28 July 2008
2 of 31
NXP Semiconductors
PCA9539; PCA9539R
16-bit I
2
C-bus and SMBus low power I/O port with interrupt and reset
5.2 Pin description
Table 3.
Symbol
INT
A1
RESET
Pin description
Pin
SO24, TSSOP24
1
2
3
HVQFN24
22
23
24
interrupt output (open-drain)
address input 1
active LOW reset input. Driving this pin LOW
causes:
Description
•
•
IO0_0
IO0_1
IO0_2
IO0_3
IO0_4
IO0_5
IO0_6
IO0_7
V
SS
IO1_0
IO1_1
IO1_2
IO1_3
IO1_4
IO1_5
IO1_6
IO1_7
A0
SCL
SDA
V
DD
[1]
PCA9539 to reset its state machine and
registers
PCA9539R to reset its state machine, but
has no effect on its registers
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
1
2
3
4
5
6
7
8
9
[1]
10
11
12
13
14
15
16
17
18
19
20
21
port 0 input/output 0
port 0 input/output 1
port 0 input/output 2
port 0 input/output 3
port 0 input/output 4
port 0 input/output 5
port 0 input/output 6
port 0 input/output 7
supply ground
port 1 input/output 0
port 1 input/output 1
port 1 input/output 2
port 1 input/output 3
port 1 input/output 4
port 1 input/output 5
port 1 input/output 6
port 1 input/output 7
address input 0
serial clock line input
serial data line open-drain input/output
supply voltage
HVQFN24 package die supply ground is connected to both V
SS
pin and exposed center pad. V
SS
pin must
be connected to supply ground for proper device operation. For enhanced thermal, electrical, and board
level performance, the exposed pad needs to be soldered to the board using a corresponding thermal pad
on the board and for proper heat conduction through the board, thermal vias need to be incorporated in the
PCB in the thermal pad region.
PCA9539_PCA9539R_5
© NXP B.V. 2008. All rights reserved.
Product data sheet
Rev. 05 — 28 July 2008
5 of 31
京公网安备 11010802033920号
EEWORLD
