PIC18LF24K50 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > PIC18LF24K50

Preview

PIC18LF24K50: DescriptionFlash Memory Programming Specification; File Size319KB，44 Pages; ManufacturerMicrochip; Websitehttps://www.microchip.com

Download Datasheet View All

PIC18LF24K50 Overview

Flash Memory Programming Specification

Preview

Download Datasheet

View All

PIC18(L)F2X/4XK50

Flash Memory Programming Specification

1.0

DEVICE OVERVIEW

Note 1:

The High-Voltage ICSP mode is always

available, regardless of the state of the

LVP bit, by applying V

IHH

to the MCLR/

/RE3 pin.

While in Low-Voltage ICSP mode, MCLR

is always enabled, regardless of the

MCLRE bit, and the RE3 pin can no

longer be used as a general purpose

input.

This

document

includes

the

programming

specifications for the following devices:

• PIC18F24K50

• PIC18F25K50

• PIC18F26K50

• PIC18F45K50

• PIC18F46K50

• PIC18LF24K50

• PIC18LF25K50

• PIC18LF26K50

• PIC18LF45K50

• PIC18LF46K50

2.0

PROGRAMMING OVERVIEW

2.2

The PIC18(L)F2X/4XK50 devices can be programmed

using either the high-voltage In-Circuit Serial

Programming™ (ICSP™) method or the low-voltage

ICSP method. Both methods can be done with the

device in the users’ system. The low-voltage ICSP

method is slightly different than the high-voltage

method and these differences are noted where

applicable. This programming specification applies to

the PIC18(L)F2X/4XK50 devices in all package types.

Dedicated ICSP/ICD Port (44-Pin

TQFP Only)

2.1

Hardware Requirements

In High-Voltage ICSP mode, the PIC18(L)F2X/4XK50

devices require two programmable power supplies:

one for V

and one for MCLR/V

/RE3. Both supplies

should have a minimum resolution of 0.25V. Refer to

Section 6.0

“AC/DC

Characteristics

Timing

Requirements for Program/Verify Test Mode”

for

additional information.

The PIC18F45K50/46K50 44-pin TQFP devices are

designed to support an alternate programming input:

the dedicated ICSP/ICD port. The primary purpose of

this port is to provide an alternate In-Circuit Debugging

(ICD) option and free the pins (RB6, RB7 and MCLR)

that would normally be used for debugging the

application. In conjunction with ICD capability,

however, the dedicated ICSP/ICD port also provides an

alternate port for ICSP. Setting the ICPRT

Configuration bit enables the dedicated ICSP/ICD port.

The dedicated ICSP/ICD port functions the same as

the default ICSP/ICD port; however, alternate pins are

used instead. Table 2-2 identifies the functionally

equivalent pins for ICSP purposes: The dedicated

ICSP/ICD port is an alternate port. Thus, ICSP is still

available through the default port even though the

ICPRT Configuration bit is set.

2.1.1

LOW-VOLTAGE ICSP

PROGRAMMING

Note:

In Low-Voltage ICSP mode, the PIC18(L)F2X/4XK50

devices can be programmed using a single V

source

in the operating range. The MCLR/V

/RE3 does not

have to be brought to a different voltage, but can

instead be left at the normal operating voltage. Refer to

Section 2.7 “Entering and Exiting Low-Voltage

ICSP Program/Verify Mode”

for additional hardware

parameters.

The ICPRT Configuration bit can only be

programmed through the default ICSP port.

By default the ICPORT Configuration bit is

enabled. When the ICPRT Configuration bit

is cleared (dedicated ICSP/ICD port is

disabled), the ICDPORTS pin should be

tied to either V

or V

on 44 TQFP

packages only. The ICPRT Configuration

bit must be maintained clear for all 28-pin

and 40-pin devices; otherwise, unexpected

operation may occur.



2012 Microchip Technology Inc.

DS41630B-page 1

Recommended Resources

Float level control circuit

LT3599 driver LED application circuit

Macro YP5-4B range hood circuit diagram

6-digit decimal counting display circuit

Gain Programmable AC Coupled Differential Amplifier Circuit

820e computer motherboard circuit diagram_61

buffer: What are the functions of BUFFER components in the circuit?...; zhonghuadianzie PCB Design

A complete NAND solution based on RL-USB and RL-FlashFS, stable and easy to use, can be safely used in mass production: [i=s]This post was last edited by ohahaha on 2018-8-31 17:47[/i] [size=4][b]A complete NAND solution based on RL-USB and RL-FlashFS, stable and easy to use, can be used in batches of products with con...; ohahaha DIY/Open Source Hardware

Can Java operate sqlce database: Can Java operate sqlce database? Has anyone done this before? Please give me some advice. Thank you....; postman Embedded System

Are you willing to develop in Japan?: My college classmate immigrated to Japan and founded an IT company in Japan, recruiting a large number of IT engineers. The programming language is not limited, and the Japanese language proficiency l...; newnew0601 Talking

TI provides LED reference design guide (Chinese): [i=s] This post was last edited by paulhyde on 2014-9-15 09:16 [/i] It contains the use of multiple LED driver devices and a simple case study...; wllyj Electronics Design Contest

Graduation Project of Single Chip Microcomputer Small System Board: Urgently needed! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! ! This topic requires the design of a single-chip microcomputer small system board, which has keyboard, display (LED, LCD), A/D, D/A and other human-mach...; liangzuolin Embedded System

Shortcut: L0 L1 L2 L3 L4 L5 L6 L7 L8 L9 LA LB LC LD LE LF LG LH LI LJ LK LL LM LN LO LP LQ LR LS LT LU LV LW LX LY LZ M0 M1 M2 M3 M4 M5 M6 M7 M8 M9 MA MB MC MD ME MF MG MH MI MJ MK ML MM MN MO MP MQ MR MS MT MU MV MW MX MY MZ N0 N1 N2 N3 N4 N5 N6 N7 N8 NA NB NC ND NE NF NG NH NI NJ NK NL NM NN NO NP NQ NR NS NT NU NV NX NZ O0 O1 O2 O3 OA OB OC OD OE OF OG OH OI OJ OK OL OM ON OP OQ OR OS OT OV OX OY OZ P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 PA PB PC PD PE PF PG PH PI PJ PK PL PM PN PO PP PQ PR PS PT PU PV PW PX PY PZ Q1 Q2 Q3 Q4 Q5 Q6 Q8 Q9 QA QB QC QE QF QG QH QK QL QM QP QR QS QT QV QW QX QY R0 R1 R2 R3 R4 R5 R6 R7 R8 R9 RA RB RC RD RE RF RG RH RI RJ RK RL RM RN RO RP RQ RR RS RT RU RV RW RX RY RZ

Popular Components