300E-112-2103 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > The connector> The connector> 300E-112-2103

300E-112-2103: DescriptionBoard Connector, 12 Contact(s), 1 Row(s), Male, Right Angle, 0.156 inch Pitch, Solder Terminal, Natural Insulator, Receptacle; CategoryThe connector The connector; File Size173KB，1 Pages; ManufacturerMethode Electronics Inc.

Download Datasheet Parametric View All

300E-112-2103 Overview

Board Connector, 12 Contact(s), 1 Row(s), Male, Right Angle, 0.156 inch Pitch, Solder Terminal, Natural Insulator, Receptacle

300E-112-2103 Parametric

Parameter Name	Attribute value
Maker	Methode Electronics Inc.
Reach Compliance Code	unknown
ECCN code	EAR99
Other features	WITH HOOKS
Board mount options	PCB EDGE LOCKING HOOK
body width	0.41 inch
subject depth	0.45 inch
body length	1.866 inch
Body/casing type	RECEPTACLE
Connector type	BOARD CONNECTOR
Contact to complete cooperation	SN-PB ON NI
Contact completed and terminated	TIN/LEAD OVER NICKEL
Contact point gender	MALE
Contact material	BRASS
contact mode	RECTANGULAR
Contact resistance	5 mΩ
Contact style	SQ PIN-SKT
Dielectric withstand voltage	1500VAC V
maximum insertion force	8.896 N
Insulation resistance	500000000000 Ω
Insulator color	NATURAL
insulator material	NYLON
Manufacturer's serial number	3000
Plug contact pitch	0.156 inch
Installation method	RIGHT ANGLE
Installation type	BOARD
Number of connectors	ONE
PCB row number	1
Number of rows loaded	1
Maximum operating temperature	105 °C
Minimum operating temperature	-40 °C
PCB contact pattern	RECTANGULAR
Rated current (signal)	7 A
Guideline	UL, CSA
reliability	COMMERCIAL
Terminal length	0.156 inch
Terminal pitch	3.9624 mm
Termination type	SOLDER
Total number of contacts	12
Evacuation force-minimum value	.556 N

Preview

Download Datasheet

View All

.156” (3.96mm)

Through Hole Right Angle Connector

3000 SERIES “TERMACON”

PART NUMBER LEGEND

30XX-XXX-XXXX

CONTACT TAIL DIMS (SEE TABLE 2)

CONTACT MATERIAL (SEE NOTE 1)

OPTIONS

2 - HIGH INSERTION FORCE CONTACT

3 - LOW INSERTION FORCE CONTACT

NO. OF POSITONS (SEE TABLE 1)

OPTIONS

WITH LEGS

WITH HOOKS

WITH HOOKS AND LOCKING RAMP

WITH LOCKING RAMP

WITH HOOKS, LOCKING RAMP AND POLARIZING KEY

WITHOUT HOOKS, W/ LOCKING RAMP AND POLARIZING KEY

CONTACT FINISH (SEE NOTE 2)

INSULATOR MATERIAL (SEE NOTE 1)

MATING HEADERS: 3100 SERIES

POLARIZING KEY &

LOCKING RAMP

LEG

HOOK

Connector Products

1700 Hicks Road • Rolling Meadows, IL 60008 USA

Telephone: 847.392.3500 • Fax: 847.392.9404

email: mcpsales@methode.com • Web Page: www.methode.com

Recommended Resources

vehicle alarm circuit

Turn short circuit detector circuit

Double rotor control circuit

Precision summing circuit

Diode detection circuit

875p computer motherboard circuit diagram_021

lm3s811 uart: uart1 needs to build its own peripherals.After configuring uart1 according to the datasheet, it still doesn't work.Later I found out that the uart0 on the board "corresponds" to the virtual serial por...; heycare Microcontroller MCU

WinCE component problem: Dear experts: Q: Does WinCE contain the following components: Similar to the device manager in WinXP, I can check what devices the system has? Whether they are enabled, etc. etc........ Thanks...........; williams Embedded System

Relationship between LED lamp life and driving power supply: [hide]Due to the particularity of LED processing and manufacturing, the current and voltage characteristics of LEDs produced by different manufacturers or even by the same manufacturer in the same bat...; 探路者 LED Zone

Comparison Solution: SAI+LM2596 Switching Voltage Regulator Solution: [i=s]This post was last edited by lonerzf on 2014-8-17 17:46[/i] In the previous design process, I encountered a situation where there was no suitable input power supply. At that time, there was only ...; lonerzf Analogue and Mixed Signal

Embedded linux recvfrom problem: S3C6410+3G module, running Linux, using udp to establish a connection with the server, sendto operates normally, data is sent successfully, and the return result is correct. The recvfrom operation fai...; HOHO Linux and Android

Is it possible to use a 5V powered crystal oscillator to provide a clock signal to a 3.3V F2407?: Everyone, I am using the TI dsp of F2407. Because it is powered by 3.3V, I wanted to buy a crystal oscillator with 3.3V power supply, but I couldn't find one. I only bought an active crystal oscillato...; xinyancode DSP and ARM Processors

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components