3062-618-3003 datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > The connector> The connector> 3062-618-3003

3062-618-3003: DescriptionBoard Connector, 18 Contact(s), 1 Row(s), Male, Right Angle, 0.156 inch Pitch, Solder Terminal, Natural Insulator, Receptacle; CategoryThe connector The connector; File Size173KB，1 Pages; ManufacturerMethode Electronics Inc.

Download Datasheet Parametric View All

3062-618-3003 Overview

Board Connector, 18 Contact(s), 1 Row(s), Male, Right Angle, 0.156 inch Pitch, Solder Terminal, Natural Insulator, Receptacle

3062-618-3003 Parametric

Parameter Name	Attribute value
Maker	Methode Electronics Inc.
Reach Compliance Code	unknown
ECCN code	EAR99
Other features	WITH LOCKING RAMP
subject depth	0.45 inch
body length	2.802 inch
Body/casing type	RECEPTACLE
Connector type	BOARD CONNECTOR
Contact to complete cooperation	AU ON NI
Contact completed and terminated	GOLD OVER NICKEL
Contact point gender	MALE
Contact material	PHOSPHOR BRONZE
contact mode	RECTANGULAR
Contact resistance	5 mΩ
Contact style	SQ PIN-SKT
Dielectric withstand voltage	1500VAC V
maximum insertion force	LIF N
Insulation resistance	500000000000 Ω
Insulator color	NATURAL
insulator material	NYLON
Manufacturer's serial number	3000
Plug contact pitch	0.156 inch
Installation method	RIGHT ANGLE
Installation type	BOARD
Number of connectors	ONE
PCB row number	1
Number of rows loaded	1
Maximum operating temperature	105 °C
Minimum operating temperature	-40 °C
PCB contact pattern	RECTANGULAR
Plating thickness	15u inch
Rated current (signal)	7 A
Guideline	UL, CSA
reliability	COMMERCIAL
Terminal length	0.156 inch
Terminal pitch	3.9624 mm
Termination type	SOLDER
Total number of contacts	18
Evacuation force-minimum value	LIF N

Preview

Download Datasheet

View All

.156” (3.96mm)

Through Hole Right Angle Connector

3000 SERIES “TERMACON”

PART NUMBER LEGEND

30XX-XXX-XXXX

CONTACT TAIL DIMS (SEE TABLE 2)

CONTACT MATERIAL (SEE NOTE 1)

OPTIONS

2 - HIGH INSERTION FORCE CONTACT

3 - LOW INSERTION FORCE CONTACT

NO. OF POSITONS (SEE TABLE 1)

OPTIONS

WITH LEGS

WITH HOOKS

WITH HOOKS AND LOCKING RAMP

WITH LOCKING RAMP

WITH HOOKS, LOCKING RAMP AND POLARIZING KEY

WITHOUT HOOKS, W/ LOCKING RAMP AND POLARIZING KEY

CONTACT FINISH (SEE NOTE 2)

INSULATOR MATERIAL (SEE NOTE 1)

MATING HEADERS: 3100 SERIES

POLARIZING KEY &

LOCKING RAMP

LEG

HOOK

Connector Products

1700 Hicks Road • Rolling Meadows, IL 60008 USA

Telephone: 847.392.3500 • Fax: 847.392.9404

email: mcpsales@methode.com • Web Page: www.methode.com

Recommended Resources

A single-section transistor performance test circuit

The working principle of the microwave oven operation display circuit

Voltage stabilization circuit diagram with adjustable output voltage

Practical soft start circuit diagram in switching power supply a

Interlock control circuit diagram of hydraulic motor of spindle motor on drilling machine

Coil partial short circuit test circuit

Sharing ARM7 learning experience - Universal Asynchronous Receiver UART (V): Before introducing the use of UART , let me first say that LPC2148 can also use serial port 0 to download programs. There are several download tools, which can be found on the Internet. I personally f...; billbot501 ARM Technology

Easy Power Trial 02: [color=#000000][font=宋体]After getting familiar with it before, I was ready to test it and found that my LMZ10504 module had no voltage output. I checked EN and other things. I spent a lot of time gett...; lyzhangxiang Analogue and Mixed Signal

Is this the correct way to connect the HC-SR501 sensor to the microcontroller?: Questions: 1. Is the connection correct? 2. Is there any problem with the program? If there is any problem with the above, how can I fix it? I have never played with 51 single-chip microcomputers, so ...; yidoumi 51mcu

Can anyone change the MAC address of the Neptune wireless network card?: Can anyone change the MAC address of the Neptune wireless network card?...; xwj521 Embedded System

20H Principle of PCB Design: [b]20H principle[/b] refers to the power layer being retracted 20H relative to the ground layer, which is also to suppress the edge radiation effect. Electromagnetic interference will be radiated outw...; 平Ｎshine PCB Design

I don’t understand the vga frame generation code!: reg [16:0] pixelcnt; reg [4:0] hscnt; reg [11:0] hscount; reg [2:0] hscnttemp; reg vga640; wire hs_temp; assign hs_temp=hs; always@(posedge tile1_txusrclk20_i) begin hscnttemp[0] <= hs_temp; hscnttemp...; xianyunyehe216 FPGA/CPLD

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components