EEWORLDEEWORLDEEWORLD

Part Number

Search

BRP3-S-10-R-10-G1

Description
Board Connector, 10 Contact(s), 1 Row(s), Male, Right Angle, 0.1 inch Pitch, Solder Terminal, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size157KB,2 Pages
ManufacturerEaton
Download Datasheet Parametric View All

BRP3-S-10-R-10-G1 Overview

Board Connector, 10 Contact(s), 1 Row(s), Male, Right Angle, 0.1 inch Pitch, Solder Terminal, Black Insulator, Receptacle

BRP3-S-10-R-10-G1 Parametric

Parameter NameAttribute value
MakerEaton
Reach Compliance Codecompliant
ECCN codeEAR99
body width0.113 inch
body length0.999 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON NI
Contact completed and terminatedGOLD
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulator colorBLACK
insulator materialGLASS FILLED THERMOPLASTIC
Manufacturer's serial numberBRP3
Plug contact pitch0.1 inch
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
PCB contact patternRECTANGULAR
GuidelineUL
reliabilityCOMMERCIAL
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts10
The simplest cpld is wrong, I am depressed, can anyone help me check it, thank you
Use cpld to connect with 51 to read external ram, where the lower 8 bits of address are latched by cpld. It seems that this program only needs a few pointers, but it is wrong when I write 0FF. Other d...
10317E Microcontroller MCU
How many clock cycles do I need to display in the console during ISE VHDL simulation?
I think I can use report, but how does report represent variables?...
timdong FPGA/CPLD
【LEFT】Can you please tell me how to read the hard disk serial number using C language programming?
[i=s]This post was last edited by Xin Xin on 2018-9-6 22:06[/i] In CCS environment, how to write a program in C language to read the physical serial number of the hard disk? It is urgent, please give ...
nanjingzhangjun Programming Basics
Transistor Failure Analysis
As shown below, why does it mean that the collector DC voltage is 0.2V, which means that the resistor R2 is short-circuited? Even if R2 is not short-circuited (normal), Uc may also be 0.2V (saturated)...
风语者之哥 Discrete Device
Have you ever encountered this problem?!
[i=s] 本帖最后由 dontium 于 2015-1-23 13:24 编辑 [/i]Can\'t Initialize Target CPU: Error 0x80002240/-172 Fatal Error during: Initialization, OCS, Control,This error was generated by TI\'s USCIF driver.SC_ERR_...
flybaby Analogue and Mixed Signal
What does this program mean? I don't understand the first two lines. Please enlighten me.
main() {unsigned long i,count=80000;unsigned char x=0;Init_Clock();Init_GPIO();while (1){if(GPIO_ReadInputPin(GPIOG, GPIO_PIN_2)==0x04)x=0;else if(x==0){x=1;if(count==80000)count=20000;else count=8000...
KCP stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 325  2310  2379  211  2290  7  47  48  5  26 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号