EEWORLDEEWORLDEEWORLD

Part Number

Search

51760-11014014CBLF

Description
Board Connector, 164 Contact(s), Female, Right Angle, Press Fit Terminal, Guide Pin, Receptacle
CategoryThe connector    The connector   
File Size259KB,3 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

51760-11014014CBLF Overview

Board Connector, 164 Contact(s), Female, Right Angle, Press Fit Terminal, Guide Pin, Receptacle

51760-11014014CBLF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
MakerAmphenol
Objectid307883164
Reach Compliance Codecompliant
ECCN codeEAR99
Board mount optionsHOLE .138-.163
body width0.47 inch
subject depth0.865 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact arrangementS140P24
Contact completed and terminatedTIN
Contact point genderFEMALE
Contact materialCOPPER ALLOY
Contact resistance20 mΩ
Contact styleHYBRID
Dielectric withstand voltage2500VDC V
Durability200 Cycles
maximum insertion force.973 N
Insulation resistance500000000 Ω
insulator materialGLASS FILLED THERMOPLASTIC
Manufacturer's serial number51760
Mixed contactsYES
Installation option 1GUIDE PIN
Installation option 2LOCKING
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
Maximum operating temperature105 °C
Minimum operating temperature-55 °C
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.154 inch
Termination typePRESS FIT
Total number of contacts164
Evacuation force-minimum value.17792 N
PDM: Rev:M
STATUS:
Released
Printed: Dec 20, 2010
.
How to expand FPGA control SDR SDRAM
I recently used FPGA to make an SDRAM controller. It was originally connected to one SDRAM, and it has been debugged OK. Now I need to expand the capacity. I don't know how to connect two SDRAMs? The ...
eeleader-mcu FPGA/CPLD
Smart Grid Power Quality Monitor-Solution Introduction
[i=s]This post was last edited by elvike on 2016-12-25 22:30[/i] [align=left][font=宋体]A word of caution before the beginning: I haven't posted anything for a long time. I went back and looked through ...
elvike Industrial Control Electronics
Questions about the use of TVS tubes and voltage regulator tubes
I have the impression that the principle used by Zener diodes and TVS tubes is that the voltage does not change much in a large current change range. Therefore, a general Zener diode is connected in s...
陈陈陈1 Analog electronics
About Magnetic Beads
I have some ferrite beads, MMZ2012 series, 60 ohm, 1000mA maximum current, I want to use it for power supply, but the data sheet of this ferrite bead says that this series is for signal line, can I us...
hsleung PCB Design
Determination of ARM s3c44b0x ISR_STARTADDRESS value
Recently, I ran an interrupt program on the s3c44b0x board, and it always failed. After considering all the situations, I think the ISR_STARTADDRESS value is a possible error. The source program defin...
doctorwu ARM Technology
Looking for CCS3.3 software
A novice is learning DSP and using a classmate's software. After installing it, for some reason a message pops up asking for a repair license, so the software cannot be opened.So I need help from you ...
buaawumeng DSP and ARM Processors

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1622  90  2102  2885  1239  33  2  43  59  25 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号