EEWORLDEEWORLDEEWORLD

Part Number

Search

PTN1005K2103BSTF

Description
RESISTOR, THIN FILM, 0.25 W, 0.1 %, 100 ppm, 210000 ohm, SURFACE MOUNT, 1005, CHIP, ROHS COMPLIANT
CategoryPassive components    The resistor   
File Size117KB,4 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Environmental Compliance  
Download Datasheet Parametric View All

PTN1005K2103BSTF Overview

RESISTOR, THIN FILM, 0.25 W, 0.1 %, 100 ppm, 210000 ohm, SURFACE MOUNT, 1005, CHIP, ROHS COMPLIANT

PTN1005K2103BSTF Parametric

Parameter NameAttribute value
Is it lead-free?Lead free
Is it Rohs certified?conform to
package instructionSMT, 1005
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresANTI-SULFUR; LASER TRIMMABLE; NON-INDUCTIVE
structureRectangular
JESD-609 codee3
Installation featuresSURFACE MOUNT
Number of terminals2
Maximum operating temperature155 °C
Minimum operating temperature-55 °C
Package height0.838 mm
Package length2.667 mm
Package formSMT
Package width1.27 mm
method of packingTR
Rated power dissipation(P)0.25 W
Rated temperature70 °C
resistance210000 Ω
Resistor typeFIXED RESISTOR
size code1005
surface mountYES
technologyTHIN FILM
Temperature Coefficient100 ppm/°C
Terminal surfaceMatte Tin (Sn) - with Nickel (Ni) barrier
Terminal shapeWRAPAROUND
Tolerance0.1%
Operating Voltage100 V
PTN
Vishay Thin Film
Commercial Thin Film Chip Resistors
FEATURES
Lead (Pb)-free or Sn/Pb terminations available
Pb-free
Moisture resistant
Available
High purity alumina substrate
RoHS*
Non-standard values available
COMPLIANT
Will pass + 85 °C, 85 % relative humidity and
10 % rated power
100 % visual inspected per MIL-PRF-55342
Very low noise and voltage coefficient (< - 30 dB)
Non-inductive
Laser-trimmed tolerances to ± 0.1 %
Wraparound resistance less than 10 mΩ
Epoxy bondable termination available
Actual Size
1505
SURFACE MOUNT
CHIPS
These chip resistors are available in both “top side” and
“wraparound” termination styles in a variety of sizes. They
incorporate self passivated, enhanced Tantalum Nitride
films, to give superior performance on moisture resistance,
voltage coefficient, power handling and resistance stability.
The terminations consist of an adhesion layer, a leach
resistant nickel barrier, and solder coating. This product will
out-perform all requirements of characteristic H of
MIL-PRF-55342.
CONSTRUCTION
Passivation
Tantalum
Nitride
Resistive Film
Solder
coating
Nickel barrier
High Purity
Alumina Substrate
Adhesion layer
TYPICAL PERFORMANCE
ABS
TCR
TOL
25
0.1
STANDARD ELECTRICAL SPECIFICATIONS
TEST
Material
Absolute TCR
Absolute Tolerance
Operating Temperature Range
Noise
CASE SIZE
0402
0502
0505
0603
0805
(1)
, 0705
(1)
1005
1010
1206
1505
2208
2010
2512
POWER RATING (mW)
50
100
150
150
200
250
500
400
400
750
800
1000
SPECIFICATIONS
Tantalum nitride
± 25 ppm/°C, ± 50 ppm/°C, ± 100 ppm/°C
± 1.0 %, ± 0.5 % and ± 0.1 %
- 55 °C to + 125 °C
< - 25 dB
MAX. WORKING VOLTAGE
75
75
75
75
100
100
150
200
150
150
200
200
RESISTANCE RANGE - (Ω)
20 - 35K
20 - 65K
20 - 130K
10 - 80K
10 - 301K
10 - 301K
50 - 600K
10 - 1M
10 - 1M
10 - 1.75M
10 - 2M
10 - 3M
- 55 °C to + 125 °C
+ 25 °C
CONDITIONS
Note
(1)
0705 and 0805 are the same (only use 0805 when ordering)
* Pb containing terminations are not RoHS compliant, exemptions may apply
Document Number: 60026
Revision: 23-Jan-09
For technical questions, contact: thin-film@vishay.com
www.vishay.com
55
BUG in wincc
When modifying variables in variable management in wincc, sometimes (often) the variable properties dialog box appears. The variable name can be changed, but when clicking to select address reallocati...
yuhuofei Industrial Control Electronics
Question about registry comments?
When compiling, PB will judge which entries to put into boot.hv based on the tags in platform.reg and Common.reg. This tag is ;HIVE BOOT SECTION ;END BOOT SECTION. When compiling, PB will put the entr...
polo_dai Embedded System
ADS1220 driver compilation error
I've been working on ADS1220 recently. I downloaded a driver from the Internet and ported it to STM32F767, but there was an error in the compilation.The error codes are as follows: /* Driver structure...
chenbingjy stm32/stm8
[Evaluation of EC-01F-Kit, the NB-IoT development board of Anxinke] + Simple networking test
We can connect it to the Internet through AT commands. So the next step is to test the simple networking of the device, mainly connecting to the OneNet cloud. Through OneNet Cloud, we conduct a simple...
流行科技 RF/Wirelessly
AD17 Why can't I import 3D models?
This warning pops up when importing a 3D model. I don't know why....
hhma PCB Design
Based on SA7527 fluorescent lamp isolation driver board
I recently bought two SA7527 fluorescent lamp isolation driver boards: suitable for T8 (large size) T10; I didn't know the IC at first, so I copied the board and drew the schematic diagram; finally, I...
czf0408 LED Zone

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2429  2765  1151  1858  2016  49  56  24  38  41 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号