[i=s] This post was last edited by Changjianze1 on 2017-4-18 08:05 [/i] [align=center][b][size=6][color=red][font=宋体]Chapter 7 [/font] Android APP [font=宋体] Let’s play with the small light [/font][/co...
[i=s] This post was last edited by tiankai001 on 2019-1-8 10:54 [/i] [b]4. Typical collector DC circuit of NPN transistor with negative power supply 2 [/b][align=left][color=rgb(34, 34, 34)][font="]Th...
Based on IPM05F 3Sh board: FOC motor control 400V sensorless and sensory encoder all design data summary (schematic diagram/BOM table/reference program/debugging instructions, etc.)IPM05F three-resist...
I modified the TI 6918 TFT connection scheme, and the screen uses the ILI9320 control chip. The code, connection circuit diagram, and TFT information are below:)...
In "If You Are the One", Mr. Le Jia once posted a microblog, which roughly said that when Mr. Le Jia was in his first love, there was a girl who loved him very much. At that time, Le Jia was poor, unr...
Recently, the first Digital China Summit was held in Fuzhou, attracting many domestic ICT industry giants to participate in the exhibition. The long queues outside the venue, the noisy and exciting...[Details]
On April 24, Sungrow released its annual financial report. The report shows that in 2017, Sungrow's global shipments reached 16.5GW, of which domestic shipments reached 13.2GW, a year-on-year incre...[Details]
Recently, the US embargo on ZTE has attracted much attention. Let's take a look at the relevant content with the automotive electronics editor. On April 16, local time, the U.S. Department of Co...[Details]
Friends who work in the photovoltaic industry, do you still remember the hard work on June 30 last year? How many people worked late into the night for months in a row just to connect to the grid a...[Details]
0. Preparation First use st-link to connect the stm32 core board and PC for burning St-link Stm32 3.3V 3.3V GND GND SWDIO PART SWCLK DCLK Then connect with USB serial port board to v...[Details]
This program mainly uses the comparison output function of the timer to generate PWM waves to control the LED. The comparison output of timer A corresponds to P2.3 P2.4. Therefore, a matching working...[Details]
1. Brief description A summary of "How to build uClinux kernel transplantation on ARMSYS development board with S3C44B0X as core", including the analysis of Bootloader function and the key co...[Details]
The implementation of CAN driver under embedded operating system Android requires not only adding CAN driver device in Linux kernel, but also implementing the call of Android HAL layer. Taking S5...[Details]
The key is the configuration of registers. The T1 timer (16 bits) of CC2530 needs to configure three registers: T1CTL, T1STAT, IRCON Here is just a brief introduction. For more details, please refer ...[Details]
Using AT89S51 microcontroller, modify the original one to turn the LED on for 4s and off for 2s. Thank you. Use a timer. (The program is written in the answer, omitted here - just a note) The origi...[Details]
MCS-51 single-chip microcomputer timer/counter experiment programming program Programming requirements: 1. Connect a light-emitting diode LED to the P1.0 pin, light up for two seconds, turn off for o...[Details]
The circuit shown in the figure requires that the light is off when the machine is turned on. Press the button once, and the light D1 will turn on and automatically turn off after a delay of 10 secon...[Details]
Microcontroller MCU
京公网安备 11010802033920号
EEWORLD
