8168S1HV6KE2 datasheet, PDF - EEWORLD Datasheet

8168S1HV6KE2: DescriptionPushbutton Switch, SPDT, On-(on), Vertical, 7 PCB Hole Cnt, Solder Terminal, Through Hole-right Angle; CategoryMechanical and electronic products switch; File Size571KB，10 Pages; ManufacturerITT; Websitehttp://www.ittcannon.com/

Download Datasheet Parametric View All

8168S1HV6KE2 Overview

Pushbutton Switch, SPDT, On-(on), Vertical, 7 PCB Hole Cnt, Solder Terminal, Through Hole-right Angle

Parameter Name	Attribute value
Reach Compliance Code	unknown
ECCN code	EAR99
Actuator angle
Actuator color	BLACK
Executor completed	GLOSS
Actuator length	0.315 inch
Actuator material	NYLON
Actuator type	PUSHBUTTON
body width	9.144 mm
body height	32.004 mm
Body length or diameter	19.05 mm
Casing diameter	0.25 inch
Nozzle length	0.3 inch
Casing type	1/4-40
Center contact plating	GOLD OVER NICKEL
Contact (DC) maximum rated power R load	0.4VA@20VDC
Contact function	ON-(ON)
Contact resistance	0.02 mΩ
Dielectric withstand voltage	1000VAC V
Electrical life	50000 Cycle(s)
End contact material	COPPER ALLOY
End contact plating	GOLD OVER NICKEL
Shell material	STAINLESS STEEL
Insulation resistance	1000000000 Ω
insulator material	GLASS FILLED NYLON
Manufacturer's serial number	8060
Installation features	THROUGH HOLE-RIGHT ANGLE
Maximum operating temperature	65 °C
Minimum operating temperature	-30 °C
PCB hole count	7
seal	EPOXY
Solderability	MIL-STD
surface mount	NO
Switch action	VERTICAL
switch function	SPDT
Switch type	PUSHBUTTON SWITCH
Terminal surface	TIN-LEAD
Terminal length	0.185 inch
Terminal material	COPPER ALLOY
Termination type	SOLDER
Washability	PARTIAL

Printed from www.freetradezone.com, a service of Partminer, Inc.

This Material Copyrighted By Its Respective Manufacturer

Help: Suggest to delete "EDA/IC Design" IC Design Rules, confidential documents, please post if you want!: It is recommended to delete the post "Confidential Document, Comments Required!" in "EDA/IC Design? IC Design Rules". This post is suspected of promoting other companies. There are so many comments be...; yfee Suggestions & Announcements

Under 6410, I used IROM_Fusing_Tool.exe to make an SD card boot disk and burned something into it, but why did the SD card capacity not change? Is it hidden?: Under 6410, I used IROM_Fusing_Tool.exe to make an SD card boot disk and burned something into it, but why did the SD card capacity not change? Is it hidden?...; htjsmhj Embedded System

DFM should not be limited to chips, PCB needs it more: We all know that even if the silicon is 100% perfect, if any one component of the chip-to-chip communication link (such as the package, connector or circuit board) is damaged, the target system may st...; clj2004000 PCB Design

Report Forum: I've been busy making an amplifier recently, so I don't have time to share my experience with M3 with you. The information is not very valuable (I think the most valuable ones have been posted), and I...; heavenji Microcontroller MCU

Introduction to Intel Embedded Systems Invitational Competition: [i=s]This post was last edited by paulhyde on 2014-9-15 09:01[/i] The "Intel Cup Undergraduate Electronic Design Competition - Embedded System Special Invitational Competition" is part of the National...; open82977352 Electronics Design Contest

Adjustment of basic idle speed of electronically controlled vehicles 3: （2006-04-04 13:20:26 ）　e. Turn off the engine after adjusting the basic idle speed, and then clear the fault code (35#) stored in the computer after disconnecting the ISCV circuit. Methods for clearin...; frozenviolet Automotive Electronics

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components