EEWORLDEEWORLDEEWORLD

Part Number

Search

8168S1HV7BE2

Description
Pushbutton Switch, SPDT, On-(on), Vertical, 7 PCB Hole Cnt, Solder Terminal, Through Hole-right Angle
CategoryMechanical and electronic products    switch   
File Size571KB,10 Pages
ManufacturerITT
Websitehttp://www.ittcannon.com/
Download Datasheet Parametric View All

8168S1HV7BE2 Overview

Pushbutton Switch, SPDT, On-(on), Vertical, 7 PCB Hole Cnt, Solder Terminal, Through Hole-right Angle

8168S1HV7BE2 Parametric

Parameter NameAttribute value
Reach Compliance Codeunknown
ECCN codeEAR99
Actuator angle
Actuator colorBLACK
Executor completedGLOSS
Actuator length0.315 inch
Actuator materialNYLON
Actuator typePUSHBUTTON
body width9.144 mm
body height36.322 mm
Body length or diameter19.05 mm
Casing diameter0.25 inch
Nozzle length0.3 inch
Casing type1/4-40
Center contact platingGOLD OVER NICKEL
Contact (DC) maximum rated power R load0.4VA@20VDC
Contact functionON-(ON)
Contact resistance0.02 mΩ
Dielectric withstand voltage1000VAC V
Electrical life50000 Cycle(s)
End contact materialCOPPER ALLOY
End contact platingGOLD OVER NICKEL
Shell materialSTAINLESS STEEL
Insulation resistance1000000000 Ω
insulator materialGLASS FILLED NYLON
Manufacturer's serial number8060
Installation featuresTHROUGH HOLE-RIGHT ANGLE
Maximum operating temperature65 °C
Minimum operating temperature-30 °C
PCB hole count7
sealEPOXY
SolderabilityMIL-STD
surface mountNO
Switch actionVERTICAL
switch functionSPDT
Switch typePUSHBUTTON SWITCH
Terminal surfaceGOLD/NICKEL
Terminal length0.185 inch
Terminal materialCOPPER ALLOY
Termination typeSOLDER
WashabilityPARTIAL
Printed from www.freetradezone.com, a service of Partminer, Inc.
This Material Copyrighted By Its Respective Manufacturer
9B96 development board routine usage instructions
9B96 development board routine instructions, who can send a copy?...
wzp2007 Microcontroller MCU
Problems with using Guard Ring when wiring op amps
When I was looking at an op amp datasheet, the layout guideline said that using a guard ring around the input wire can greatly reduce leakage current. I didn't really understand what a guard ring is....
zpccx PCB Design
Buffered I/O Example Program
Now let's look at an example. The program first defines a structure called pirate, and then declares two variables of this type. The program initializes one of the variables and writes it to the disk ...
chenbingjy Linux and Android
Discussion on PCB layout for weak signal measurement
[table=98%,rgb(238, 238, 238)] [tr][td] For PCB layout (op amp, AD, DA, reference) of weak signal measurement (μV or even nV level), can the reference be laid on a separate layer (4-layer board)? Will...
zca123 PCB Design
BGA DIY manual soldering problem solving
[i=s] This post was last edited by Qingye Piaoling on 2015-4-21 11:07 [/i] After a long period of thinking and improvement of comprehensive ability. The difference in success rate between BGA manual s...
青叶漂零 DIY/Open Source Hardware
I would like to ask everyone, which direction is better to develop in, software engineering or embedded system?
I am from the Department of Computer Science. In my junior year, I was divided into two majors: software engineering and embedded system. I would like to know more about what the two majors are about....
flyingxc82 Embedded System

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 403  2629  426  1842  723  9  53  38  15  40 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号