EEWORLDEEWORLDEEWORLD

Part Number

Search

51740-10800812ALF

Description
Board Connector, Female, Right Angle, Solder Terminal, Locking, Receptacle
CategoryThe connector    The connector   
File Size243KB,3 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

51740-10800812ALF Overview

Board Connector, Female, Right Angle, Solder Terminal, Locking, Receptacle

51740-10800812ALF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Reach Compliance Codecompliant
ECCN codeEAR99
Board mount optionsSPLIT BOARD LOCK
body width0.47 inch
subject depth0.5 inch
body length5.85 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact completed and terminatedTin (Sn)
Contact point genderFEMALE
Contact materialCOPPER ALLOY
Contact resistance20 mΩ
Contact styleHYBRID
Dielectric withstand voltage2500VDC V
Durability200 Cycles
maximum insertion force.973 N
Insulation resistance10000000000 Ω
insulator materialGLASS FILLED THERMOPLASTIC
JESD-609 codee3
Manufacturer's serial number51740
Mixed contactsYES
Installation option 1LOCKING
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
Maximum operating temperature125 °C
Minimum operating temperature-55 °C
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.135 inch
Termination typeSOLDER
Evacuation force-minimum value.17792 N
PDM: Rev:R
STATUS:
Released
Printed: Dec 20, 2010
.
In the second week, when testing the single propeller with the BeagleBone development board chip, I found that it was fake.
The board has been made for a while. I didn't pay much attention to the full performance test on it before. The M3 M4 series is also good at brushless motor projects, so I didn't pay much attention to...
PENGSHIFANG DSP and ARM Processors
ISM330DLC three-axis acceleration + three-axis angular velocity sensor package and code
Data sheet:Code:Package:Official evaluation board gerber file:...
littleshrimp MEMS sensors
Altium Designer operation process and brief introduction
Altium Designer, referred to as AD, is a hardware development software. Let's take AD18 as an example to explain the simple operation process of AD. If you want to use AD to design a board, the most b...
电鱼电子工程师 PCB Design
Commonly used subroutines for single chip microcomputers
[i=s] This post was last edited by paulhyde on 2014-9-15 09:28 [/i] There are many commonly used module programs. I hope it will be helpful to beginners and make it easier to get started~~...
xianghong123 Electronics Design Contest
DAC adjusts the output voltage of DCDC chip
As shown in the figure below, the higher the DAC voltage, the lower the output voltageHowever, actual circuits have found that there is an inflection point. Before the inflection point, this relations...
sfcsdc Analog electronics
What is the principle of this inductor?
Connect one end of each leg and twist the other end together to ground. What is the principle, the effect of hair raising, and how to know the inductance value?...
lhycpqq Analog electronics

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1256  1351  13  889  1822  26  28  1  18  37 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号