EEWORLDEEWORLDEEWORLD

Part Number

Search

54111-811-02-1400

Description
Board Connector, 2 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle,
CategoryThe connector    The connector   
File Size63KB,1 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

54111-811-02-1400 Overview

Board Connector, 2 Contact(s), 1 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle,

54111-811-02-1400 Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Reach Compliance Codecompliant
ECCN codeEAR99
body width0.094 inch
subject depth0.551 inch
body length0.2 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU ON NI
Contact completed and terminatedTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialTHERMOPLASTIC
JESD-609 codee0
Manufacturer's serial number54111
Plug contact pitch0.1 inch
Installation option 1LOCKING
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
Plating thickness30u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.095 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts2
PDM: Rev:E
STATUS:
Released
Printed: Jun 03, 2008
.
Comparison of several typical connection methods of optocoupler isolation in switching power supply
In general isolated power supplies, optocoupler isolated feedback is a simple and low-cost method. However, there has been no in-depth research on the various connection methods and differences of opt...
qwqwqw2088 Analogue and Mixed Signal
DSP Programming--5.31--Hardware Interrupt Management
[size=4]In order to correctly respond to hardware interrupts and for the stability of the DSP/BIOS kernel, please pay special attention to the following points when writing HWI hardware ISRs: [/size] ...
Jacktang DSP and ARM Processors
[Xianji HPM6750 Review] Testing CAN Transceiver
HPM6750 has 4 CAN controllers and supports CANFD. Currently, CAN2.0 is more commonly used in industry, so this evaluation uses CAN1 controller. The CAN driver chip uses TI's VD230, and the computer us...
xiashuang Domestic Chip Exchange
MSP430F5529 clock and FLL configuration
1. Basic1.5529 contains five clock sourcesXT1CLK: external low-frequency crystal oscillator, 32.786KHz, can be used as FLL reference power supply, can also be adjusted from 4MHZ to 32MhzXT2CLK: extern...
灞波儿奔 Microcontroller MCU
Is there something wrong with the official library?
1. I2C initialization: #define [b]I2C_AcknowledgedAddress_7bit [/b]((uint16_t)0x4000) #define I2C_SLAVE_ADDRESS7 0xA0 /*!OAR1 = (I2C_InitStruct->[b]I2C_AcknowledgedAddress [/b]| I2C_InitStruct->I2C_Ow...
381082014 stm32/stm8

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2049  935  2035  954  486  42  19  41  20  10 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号