Y1628336R000A9R datasheet, PDF

Datasheet> All Categories > Passive components> The resistor> Y1628336R000A9R

Y1628336R000A9R: DescriptionFixed Resistor, Metal Foil, 0.75W, 336ohm, 220V, 0.05% +/-Tol, -.2,.2ppm/Cel, 2512,; CategoryPassive components The resistor; File Size2MB，6 Pages; ManufacturerVishay; Websitehttp://www.vishay.com; Environmental Compliance

Download Datasheet Parametric View All

Y1628336R000A9R Overview

Fixed Resistor, Metal Foil, 0.75W, 336ohm, 220V, 0.05% +/-Tol, -.2,.2ppm/Cel, 2512,

Y1628336R000A9R Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Reach Compliance Code	compliant
ECCN code	EAR99
structure	Chip
Number of terminals	2
Maximum operating temperature	150 °C
Minimum operating temperature	-55 °C
Package height	0.64 mm
Package length	6.32 mm
Package form	SMT
Package width	3.23 mm
method of packing	TR
Rated power dissipation(P)	0.75 W
resistance	336 Ω
Resistor type	FIXED RESISTOR
series	VSMP
size code	2512
technology	METAL FOIL
Temperature Coefficient	-.2,.2 ppm/°C
Terminal surface	Tin/Silver/Copper - with Nickel barrier
Tolerance	0.05%
Operating Voltage	220 V

Preview

Download Datasheet

View All

VSMP Series (0603, 0805, 1206, 1506, 2010, 2018, 2512)

(Z-Foil)

Ultra High Precision Foil Wraparound Surface Mount Chip Resistor

with TCR of ± 0.05 ppm/°C and Power Coefficient of 5 ppm at

Rated Power and Load Life Stability of ± 0.005 % (50 ppm)

FEATURES



Temperature coefficient of resistance (TCR):

0.05 ppm/°C typical (0 °C to + 60 °C)

0.2 ppm/°C typical (- 55 °C to + 125 °C, + 25 °C ref.)



Resistance tolerance: to ± 0.01 %



Power coefficient “R due to self heating”:

5 ppm at rated power



Power rating: to 750 mW at + 70 °C (see table 3)



Load life stability: to ± 0.005 % at 70 °C, 2000 h at rated

power



Resistance range: 5



to 125 k (for lower or higher

values, please contact us)



Vishay Foil resistors are not restricted to standard values,

we can supply specific “as required” values at no extra cost

or delivery (e.g. 1K2345 vs. 1K)



Thermal stabilization time < 1 s



(nominal value achieved within 10 ppm of steady state

value)



Electrostatic discharge (ESD) at least to 25 kV



Short time overload:



0.005 %



Non inductive, non capacitive design



Rise time: 1 ns effectively no ringing



Current noise: 0.010 µV

RMS

/V of applied voltage

(< - 40 dB)



Voltage coefficient < 0.1 ppm/V



Non inductive: < 0.08 µH



Non hot spot design



Terminal finishes available: lead (Pb)-free, tin/lead alloy



Matched sets are available on request



Prototype quantities available in just 5 working days

or sooner. For more information, please contact

foil@vpgsensors.com

Top View

(for date code print specification please refer to table 2)

INTRODUCTION

VSMP Series is the industry’s first device to provide high

rated power and excellent load life stability along with

extremely low TCR — all in one resistor.

One of the most important parameters influencing stability is

the Temperature Coefficient of Resistance (TCR). Although

the TCR of foil resistors is considered extremely low, this

characteristic has been further refined over the years. The

VSMP Series utilizes ultra high precision Bulk Metal

Z-Foil.

The Z-Foil technology provides a significant reduction of the

resistive element’s sensitivity to ambient temperature

variations (TCR) and to self heating when power is applied

(Power Coefficient of Resistance, or PCR). Along with the

inherently low PCR and TCR, Z-Foil technology also

provides remarkably improved load life stability, low noise

and tight tolerances.

The VSMP resistor has a full wraparound termination which

assures secure contact during the manufacturing process,

as well as providing stability during multiple thermal cyclings.

Vishay Foil Resistors' (VFR) application engineering

department is available to advise and make

recommendations. For non-standard technical requirements

and special applications, please contact VFR using the

e-mail address in the footer below.

Percent of Rated Power

TABLE 1 - TOLERANCE AND TCR VS.

RESISTANCE VALUE

(1)

(- 55 °C to + 125 °C, + 25 °C Ref.)

RESISTANCE

VALUE

()

250to 125K

100to < 250

50to < 100

25to < 50

10to < 25

5 to < 10

TOLERANCE

(%)

± 0.01

± 0.02

± 0.05

± 0.1

± 0.25

± 0.5

TYPICAL TCR AND

MAX. SPREAD

(ppm/°C)

± 0.2 ± 1.8

± 0.2 ± 2.8

± 0.2 ± 3.8

± 0.2 ± 7.8

FIGURE 1 - POWER DERATING CURVE

- 55 °C

100

- 75

+ 70 °C

- 50

- 25

+ 25 + 50 + 75 + 100 + 125 + 150 + 175

Ambient Temperature (°C)

* Pb containing terminations are not RoHS compliant; exemptions

may apply

Note

(1)

For tighter performances and non-standard values lower than



and above 125K, please contact VFR’s application

engineering using the e-mail addresses in the footer below

Document Number: 63060

Revision: 3-Mar-15

For any questions, contact

foil@vpgsensors.com

www.vishayfoilresistors.com

Recommended Resources

HT-8654 circuit

AC automatic voltage regulator circuit diagram

Amplifier timer.gif

CMOS555 oscillator circuit diagram that generates a full square wave

Wind speed-frequency conversion circuit

Light controlled power outage alarm

【CN0067】Fully isolated input module based on ADC AD7793, ADuM5401 and high performance instrumentation amplifier: Circuit Function and AdvantagesThis circuit provides a complete industrial control input module solution. The design is suitable for process control programmable logic controllers (PLCs) and distribut...; EEWORLD社区 ADI Reference Circuit

Can you explain the key judgment in detail?: As the title says, the following is the key judgment. I am a novice, please tell me how the following judgment works. If you can give me more details, I will give you 100 points as a reward! if ((KeyV...; mdjwmy Embedded System

Why does the package imported into the PCB have no flying leads?: [i=s]This post was last edited by qwqwqw2088 on 2017-12-20 19:54[/i] [b][size=3]There are generally three situations when there are no flying wires after importing the PCB: [/size][/b] [b][size=3] 1. ...; qwqwqw2088 PCB Design

#AugustModification #MadCatz RAT3 Superficial Modification: Disassembly is going on in the forums. I am here to join in the fun. There are not many things I can disassemble at home (I am really a spendthrift...). I saw that some netizens made a heated mouse, a...; ljj3166 DIY/Open Source Hardware

The usbdemo code can run in flash but not in ram? (The problem has been solved): IAR EWARM 4.41 & JLink & STR912FW44 & Windows 2003I copied the interrupt vector table to the highest end of ram, a total of 64bytes.In flash, there are no problems with interrupts. But it is not norma...; wqj1212 stm32/stm8

The first impression of a so-called ARM Linux development board SinLinx: Not even as good as a toy: [i=s]This post was last edited by Xin Xin on 2015-1-18 17:43[/i] [size=5][color=#0000ff]Chenzhufully is right, this name is too misleading, and it is easy for me to present an image of ignorance and a...; 辛昕 Linux and Android

Shortcut: E0 E1 E2 E3 E4 E5 E6 E7 E8 E9 EA EB EC ED EE EF EG EH EI EJ EK EL EM EN EO EP EQ ER ES ET EU EV EW EX EY EZ F0 F1 F2 F3 F4 F5 F6 F7 F8 F9 FA FB FC FD FE FF FG FH FI FJ FK FL FM FN FO FP FQ FR FS FT FU FV FW FX FY FZ G0 G1 G2 G3 G4 G5 G6 G7 G8 G9 GA GB GC GD GE GF GG GH GI GJ GK GL GM GN GO GP GQ GR GS GT GU GV GW GX GZ H0 H1 H2 H3 H4 H5 H6 H7 H8 HA HB HC HD HE HF HG HH HI HJ HK HL HM HN HO HP HQ HR HS HT HU HV HW HX HY HZ I1 I2 I3 I4 I5 I6 I7 IA IB IC ID IE IF IG IH II IK IL IM IN IO IP IQ IR IS IT IU IV IW IX J0 J1 J2 J6 J7 JA JB JC JD JE JF JG JH JJ JK JL JM JN JP JQ JR JS JT JV JW JX JZ K0 K1 K2 K3 K4 K5 K6 K7 K8 K9 KA KB KC KD KE KF KG KH KI KJ KK KL KM KN KO KP KQ KR KS KT KU KV KW KX KY KZ

Popular Components