EEWORLDEEWORLDEEWORLD

Part Number

Search

Y4028025R8000V0C

Description
Fixed Resistor, Metal Foil, 0.2W, 25.8ohm, 0.005% +/-Tol, -.6,.6ppm/Cel
CategoryPassive components    The resistor   
File Size424KB,4 Pages
ManufacturerVishay
Websitehttp://www.vishay.com
Download Datasheet Parametric View All

Y4028025R8000V0C Overview

Fixed Resistor, Metal Foil, 0.2W, 25.8ohm, 0.005% +/-Tol, -.6,.6ppm/Cel

Y4028025R8000V0C Parametric

Parameter NameAttribute value
Reach Compliance Codecompliant
ECCN codeEAR99
structureRectangular
Manufacturer's serial numberFSR
Number of terminals2
Maximum operating temperature45 °C
Minimum operating temperature15 °C
Package height19.94 mm
Package length57.4 mm
Package shapeRECTANGULAR PACKAGE
Package formQuick Connect
Package width38.354 mm
Rated power dissipation(P)0.2 W
resistance25.8 Ω
Resistor typeFIXED RESISTOR
seriesFSR
technologyMETAL FOIL
Temperature Coefficient-.6,.6 ppm/°C
Tolerance0.005%
FSR (Secondary Standard Foil Resistor)
Vishay Foil Resistors
Bulk Metal
®
Foil Resistor Standard with TCR of 0.3 ppm/°C,
High Stability and Accuracy for Laboratory Calibration Standards
Direct Plug-In Device for Most DMM’S Available in the Market
FEATURES
• Temperature coefficient of resistance (TCR):
To ±0.3 ppm/°C (+15°C to +45°C) (see Table 1)
• Max TCR: 10 to 30 ppm window (see Figure 3)
• Resistance range: 1Ω to 150 kΩ (for higher and lower
values, please contact Applications Engineering)
Available up to six significant digits (e.g., 9K99962)
Resistance tolerance available for ordering: to
±0.005% (50 ppm)
High accuracy: to 10 ppm (see Table 1)
INTRODUCTION
A manufacturer of the most precise production-size
resistors available, Vishay Foil Resistors (VFR) has
experienced the problems presented by virtually all
available conventional and specialized secondary
standards. Among these are: instrument accuracy,
resistance shifts caused by load, temperature or
environmental changes, difficulty in measurement of
last digits, limitation on usable frequency, size and ease
of setting.
From intensive analysis of these problems, VFR
has developed a complete new design. With the
unequalled combination of the Bulk Metal
®
Foil resistor’s
performances, Vishay Foil resistors offer accuracy,
stability and versatility never before combined in a
secondary standard resistor.
The FSR reduces these major problems to insignificance:
accuracy, resistance shift, frequency, and size.
Our Application Engineering department is available to
advise and make recommendations.
For non-standard technical requirements and special
applications, please contact us via email.
Note
(1)
Measured by comparison against Vishay Foil Resistor
standards which are traceable to NIST.
Stability: ±0.0005% (5 ppm) at 25°C, 12 months
• No humidity effect: resistive element hermetically
sealed against moisture
• Small size and robust construction
• Direct plug-in device for most DMM’s available in the
market
• Each unit is supplied with certificate of accuracy
(1)
• RF shielded case
• Four terminal constructions with an additional
ground socket
Vishay Foil resistors are not restricted to standard
values; specific “as required” values can be
supplied at no additional cost or delivery time
(e.g., 1K23456 vs. 1K)
• Thermal stabilization time <1 s (nominal value achieved
within 10 ppm of steady state value)
• Electrostatic discharge (ESD) at least to 25 kV
• Rise time: 1 ns effectively no ringing
• Current noise: 0.010 μVRMS/V of applied voltage
(<-40 dB)
• Voltage coefficient: 0.1 ppm/V
• Non inductive: 0.08 μH
• Non hot spot design
FIGURE 1—DEMONSTRATION FOR EASE OF INSTALLATION ON DMM
Document Number: 63223
Revision: 12-Sep-2011
For technical questions, contact:
foil@vishaypg.com
www.vishayfoilresistors.com
1
Manually set simulation signals in modelsim
1. Create a new project : file-new-project 2. Create a new file : 3. Compile the file: compile-all 4.Simulation : simulation-start simulation: in the pop-up dialog box, select work- corresponding file...
cdy200824 FPGA/CPLD
How did a switching power supply without an inductor survive? Learn the latest course on the early history of switching power supplies
[align=left][size=4][color=#ff0000][b]Can a switching power supply without an inductor be used? [/b][/color][/size]{:1_146:}Of course it can. It is older than the switching power supply with integrate...
DreamerJane maychang Fun Electronics
How to use wm_text message?
An edit control with id IDC_EDIT1 is added to the window, and then a button with id ID_CHECK is added. The idea is that when the check button is clicked, a messagebox will pop up to display the edit c...
rockybest Embedded System
Also on the analysis of "process capability index" in chip production
During the production of chips, they will go through many processes such as doping, layer addition, photolithography and heat treatment, and each step must meet extremely demanding physical property r...
clj2004000 PCB Design
Analog electronics elective test + DC and AC parameters
https://training.eeworld.com.cn/TI/video/12740...
jean1 TI Technology Forum
Use of fir2 (in digital equalization)
[i=s]This post was last edited by paulhyde on 2014-9-15 03:42[/i] I have a problem with matlab. I want to make a simple digital equalizer. By measuring the spectrum of a simple low-pass filter, I use ...
一直一米 Electronics Design Contest

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 658  2836  93  2791  1816  14  58  2  57  37 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号