EEWORLDEEWORLDEEWORLD

Part Number

Search

S-3-NIL-6V

Description
4 AMP POLARIZED HIGH DENSITY RELAY
File Size417KB,5 Pages
ManufacturerPanasonic
Websitehttp://www.panasonic.co.jp/semicon/e-index.html
Download Datasheet View All

S-3-NIL-6V Overview

4 AMP POLARIZED HIGH DENSITY RELAY

4 AMP POLARIZED HIGH
DENSITY RELAY WITH HIGH
SENSITIVITY
FEATURES
28.0
1.102
12.0
.472
10.4
.409
S-RELAYS
• Wide switching range From 100µA
100 mV DC to 4 A 250 V AC
• Low thermal electromotive force Ap-
prox. 3
µV
• Dual-In-Line packaging arrangement
mm
inch
• A variety of contact arrangements 2
Form A 2 Form B, 3 Form A 1 Form B,
4 Form A
• Latching types available
• High sensitivity in small size 100 mW
pick-up and 200 mW nominal operat-
ing power
• High shock and vibration resistance
Shock: 50 G Vibration: 10 to 55 Hz at
double amplitude of 3 mm
SPECIFICATIONS
Contacts
Arrangement
Initial contact resistance, max.
(By voltage drop 6 V DC 1 A)
Initial contact pressure
Initial contact bounce, max.
Contact material
Electrostatic capacitance
Thermal electromotive force
(at nominal coil voltage)
Nominal switching capacity
Maximum switching power
Rating
(resistive)
2 Form A 2 Form B,
3 Form A 1 Form B,
4 Form A
50 m
Approx. 12 g
.42 oz
1 ms
Gold clad silver alloy
Approx. 3pF
Approx. 3
µ
V
4 A 250 V AC, 3 A 30 V DC
Characteristics (at 25°C
77°F
50% Relative humidity)
Max. operating speed
Initial insulation resistance*
1
Between open contacts
Between contact sets
Between contacts and
coil
Operate time*
3
(at nominal voltage)(at 20
°
C)
Release time (without diode)*
3
(at nominal voltage)(at 20
°
C)
Set time*
3
(latching)
(at nominal voltage)(at 20
°
C)
Reset time*
3
(latching)
(at nominal voltage)(at 20
°
C)
Initial contact bounce, max.
Temperature rise
(at nominal voltage)(at 20
°
C)
Shock resistance
Approx. 100 mW
Approx. 200 mW
Approx. 100 mW
Approx. 200 mW
Functional*
4
Destructive*
5
Functional*
6
Vibration resistance
Destructive
Conditions for operation,
Ambient
transport and storage*
7
temp.
(Not freezing and condens-
Humidity
ing at low temperature)
Unit weight
Initial
breakdown
voltage*
2
20 cpm for maximum load,
50 cps for low-level load
(1 mA 1 V DC)
10,000 M
at 500 V DC
750 Vrms
1,000 Vrms
1,500 Vrms
Max. 15 ms (Approx. 8 ms)
Max. 10 ms (Approx. 5 ms)
Max. 15 ms (Approx. 8 ms)
Max. 15 ms (Approx. 8 ms)
1 ms
Max. 35
°
C with nominal coil
voltage and at maximum
switching current
Min. 490 m/s
2
{50 G}
Min. 980 m/s
2
{100 G}
176.4 m/s
2
{18 G}, 10 to 55 Hz
at double amplitude of 3 mm
235.2 m/s
2
{24 G}, 10 to 55 Hz
at double amplitude of 4 mm
–40
°
C to +65
°
C
–40
°
F to +149
°
F
5 to 85% R.H.
Approx. 8 g
.28 oz
1,000 VA, 90 W
250 V AC, 30 V DC
Maximum switching voltage
(48 VDC at less than 0.5 A)
Max. switching current
4 A (AC), 3 A (DC)
Min. switching capacity**
1
100
µ
A 100 m V DC
10
8
10
5
2
×
10
5
Mechanical (at 50 cps)
4 A 250 V AC
Electrical
(at 20 cpm) 3 A 30 V DC
Expected
life (min.
operations)
Coil (polarized) (at 20°C
68°F)
Single side
stable
Latching
Notes:
**
1
This value can change due to the switching frequency, environmental conditions,
and desired reliability level, therefore it is recommended to check this with the
actual load.
Minimum operating power
Nominal operating power
Minimum set and reset
Nominal set and reset
Remarks
* Specifications will vary with foreign standards certification ratings.
*
1
Measurement at same location as "Initial breakdown voltage "section
*
2
Detection current: 10mA
*
3
Excluding contact bounce time
*
4
Half-wave pulse of sine wave: 11ms; detection time: 10
µ
s
*
5
Half-wave pulse of sine wave: 6ms
*
6
Detection time: 10
µ
s
*
7
Refer to 5. Conditions for operation, transport and storage mentioned in AMBIENT ENVIRONMENT (Page 61).
TYPICAL APPLICATIONS
Telecommunications equipment, data processing equipment,
facsimiles, alarm equipment, measuring equipment.
219
Kernel compilation error
我的编译器: arm-linux-gcc3.4.1, 内核2.6.14.1, 执行make bzImage, 出现下列错误: drivers/video/console/vgacon.c:152: warning: comparison is always true due to limited range of data type drivers/video/console/vgacon.c: ...
wonderglass Embedded System
How often should flying probe test probes be replaced?
Flying probe test probes have different service lives according to the type of metal plated on their surface. Most manufacturers use probes with relatively good quality gold-plated surface. When the s...
SMT1996 Test/Measurement
Learn about SPICE for circuit simulation
The technology of simulation using software has been widely used in the design and evaluation of electronic circuits. There are many reasons for this. For example, with the increase in speed of operat...
qwqwqw2088 Analogue and Mixed Signal
How to generate the usbser.dll library in PB6?
I use PB6+VS2005 to build CE system. I found a problem. In common.bib; @CESYSGEN IF CE_MODULES_USBSER usbser.dll $(_FLATRELEASEDIR)\usbser.dll NK SHK ; @CESYSGEN ENDIF CE_MODULES_USBSER If I comment o...
guoshixu The Industrial Cloud
pb4.2 may only add support for MFC when customizing the SDK
I am using Samsung 2410 CPU. Because the BSP of the DEMO board manufacturer does not provide MFC support, I can compile successfully with the manufacturer's BSP, but after I added MFC on the basis of ...
cosmo.wu Embedded System
Smart car
[i=s]This post was last edited by paulhyde on 2014-9-15 09:24[/i] Smart Car...
tmstd Electronics Design Contest

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2727  2441  850  555  1253  55  50  18  12  26 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号