EEWORLDEEWORLDEEWORLD

Part Number

Search

D-SUB-205AJ09YATBBB3

Description
D Type Connector, 9 Contact(s), Female, 0.109 inch Pitch, Solder Terminal, #4-40, Plug
CategoryThe connector    The connector   
File Size124KB,1 Pages
ManufacturerPalPilot
Download Datasheet Parametric View All

D-SUB-205AJ09YATBBB3 Overview

D Type Connector, 9 Contact(s), Female, 0.109 inch Pitch, Solder Terminal, #4-40, Plug

D-SUB-205AJ09YATBBB3 Parametric

Parameter NameAttribute value
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresROHS COMPLIANT,HEX-SCREWS
body width0.492 inch
subject depth0.492 inch
body length1.213 inch
Body/casing typePLUG
Contact to complete cooperationAU ON NI
Contact completed and terminatedTIN OVER NICKEL
Contact point genderFEMALE
Contact materialCOPPER ALLOY
contact modeSTAGGERED
Contact resistance15 mΩ
Contact styleRND PIN-SKT
Dielectric withstand voltage1000VAC V
Insulation resistance3000000000 Ω
Insulator colorBLACK
insulator materialPOLYBUTYLENE TEREPHTHALATE
Manufacturer's serial number205
Plug contact pitch0.109 inch
Match contact row spacing0.112 inch
Installation option 1#4-40
Installation option 2RIVET
Installation methodRIGHT ANGLE
Installation typeBOARD
PCB row number2
Number of rows loaded2
Maximum operating temperature105 °C
Minimum operating temperature-55 °C
PCB contact patternSTAGGERED
PCB contact row spacing2.8448 mm
Plating thickness5u inch
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Shell surfaceTIN
Shell materialSTEEL
Terminal length0.125 inch
Terminal pitch2.7686 mm
Termination typeSOLDER
Total number of contacts9
Multisim simulation problem
The circuit is connected as shown in the figure. Is the waveform measured at the blue test point related to the resistance and capacitance on both sides? Will the resistor R3 affect the waveform ampli...
djc天一 Analog electronics
USB communication problem in wince4.2
I need to make a program to communicate with an application in wince through usb. Since the lower computer has not been written yet, do you have a simple program that I can run in wince to test my upp...
blackholes522 Embedded System
Why is FPGA difficult to learn?
...
至芯科技FPGA大牛 FPGA/CPLD
I'm making a small product, but I don't know what to buy for the display. I've never done this before.
As long as it is bigger than the electronic watch screen and cheaper, it will be fine. 1602 seems too ugly and can't display Chinese. Now I want to use 5110 screen. I wonder if there are other similar...
huang91 MCU
FLASH runs slowly!
My fft program has a simulation speed of 100 Us in RAM, but when the program is burned into FLASH, the execution speed is several times slower, nearly one ms. How can I solve this problem?...
liyanjun120 Analogue and Mixed Signal
Why does the DIY capacitor spot welder have no current after spot welding once?
After the spot welding is turned on once, there is no current output. And the capacitor voltage is pulled down to 1v, and it slowly rises back to the original voltage after releasing the welding pen. ...
peb188 MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2377  467  199  1507  2580  48  10  5  31  52 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号