EEWORLDEEWORLDEEWORLD

Part Number

Search

BSTCR-206-S-090-10-T-100

Description
Board Connector, 6 Contact(s), 1 Row(s), Male, Right Angle, 0.079 inch Pitch, Solder Terminal, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size160KB,1 Pages
ManufacturerMajor League Electronics
Websitehttp://www.mlelectronics.com/
Download Datasheet Parametric View All

BSTCR-206-S-090-10-T-100 Overview

Board Connector, 6 Contact(s), 1 Row(s), Male, Right Angle, 0.079 inch Pitch, Solder Terminal, Black Insulator, Receptacle

BSTCR-206-S-090-10-T-100 Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresBOARD STACKING CONNECTOR
body width0.14 inch
subject depth0.109 inch
body length0.474 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationTIN LEAD (200) OVER NICKEL (50)
Contact completed and terminatedTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialGLASS FILLED POLYESTER
JESD-609 codee0
Manufacturer's serial numberBSTCR
Plug contact pitch0.079 inch
Installation methodRIGHT ANGLE
Installation typeBOARD
Number of connectorsONE
PCB row number1
Number of rows loaded1
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
Plating thickness200u inch
Rated current (signal)2 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.09 inch
Terminal pitch2.0066 mm
Termination typeSOLDER
Total number of contacts6
What causes the error "Illegal opcode found on address 0x0" during debugging?
As the title says, what causes the error "Illegal opcode found on address 0x0" during debugging? Illegal operand found?...
wangkj22 Microcontroller MCU
How to create a two-dimensional table in stm32f407
I have a set of current-angle-flux data. I want to create a table in stm32 to get the flux data based on the input current and angle. Is there any simple way to do this? The table data is quite large....
syn222 Embedded System
Show the process of WEBENCH design + LM25010
1. Design a 3.3V power outputThe power chip is LM25010. 2. Simulate this circuitOutput voltage waveformThere is a 0.05V voltage ripple.Switch tube voltage and output current waveformFrom the switch tu...
billjing Analogue and Mixed Signal
Electronic combination lock
The password lock consists of three parts: a 6V dry battery, an electric control board, and an electromagnetic relay lock. The password lock keyboard operation and the corresponding internal actions a...
rain MCU
A question about device expansion in Sfilter
Sfilter.c中的设备扩展定义如下:typedef struct _SFILTER_DEVICE_EXTENSION {ULONG TypeFlag;////Pointer to the file system device object we are attached to//PDEVICE_OBJECT AttachedToDeviceObject;////Pointer to the r...
zdy2005 Embedded System
Modify device type
To modify the device type, you need to add NV_INIT. If you don't add it, you can't configure the device type through NV read and write. You also need to add SOFT_START, BULID_ALL_DEVICES and HOLD_AUTO...
wateras1 RF/Wirelessly

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 168  128  2524  160  2479  4  3  51  50  54 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号