EEWORLDEEWORLDEEWORLD

Part Number

Search

54122-412-45-2500RLF

Description
Board Connector, 90 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Kinked Leads Terminal, Locking, Black Insulator, Receptacle
CategoryThe connector    The connector   
File Size107KB,1 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Environmental Compliance
Download Datasheet Parametric View All

54122-412-45-2500RLF Overview

Board Connector, 90 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Kinked Leads Terminal, Locking, Black Insulator, Receptacle

54122-412-45-2500RLF Parametric

Parameter NameAttribute value
Is it Rohs certified?conform to
Reach Compliance Codecompliant
ECCN codeEAR99
body width0.19 inch
subject depth0.984 inch
body length4.5 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationSN ON NI
Contact completed and terminatedMatte Tin (Sn) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialTHERMOPLASTIC
JESD-609 codee3
Manufacturer's serial number54122
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Installation option 1LOCKING
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.54 mm
Plating thickness79u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.12 inch
Terminal pitch2.54 mm
Termination typeSOLDER KINKED LEADS
Total number of contacts90
PDM: Rev:K
STATUS:
Released
Printed: Mar 10, 2011
.
Help with op amp output sine wave signal analysis
Please help me analyze the operation of this circuit.There should be a sine wave output on the left side of R2, but I can't see it in the simulation. I don't know what the problem is....
zslhhxxttxs Analog electronics
[Original] Introduction, selection and use of adjustable resistors. The difference and connection between adjustable resistors and potentiometers
[url=http://blog.ednchina.com/freeeedoooom/187414/message.aspx]http://blog.ednchina.com/freeeedoooom/187414/message.aspx[/url]...
freeeedoooom Analog electronics
LaunchPad+G2553 as USB--I2C debugging tool
This is mainly used to debug the G2452 RTC chip I made a while ago. I didn't have any ready-made tools, so I came up with this solution. I also learned about the USCI UART module by the way. In the en...
karajanlee Microcontroller MCU
CAN bus communication
Under WINCE, I want to complete the CAN bus communication function by calling WIN32 functions, that is, get the handle of CAN1 through CreateFile(), and then perform send and receive operations by cal...
jjphero Embedded System
STM32 DMAAD sampling value drift
I have a device made with STM32F103VC. I used to use injection mode (all three ADs were used). The sampling zero drift was very small, basically within 1 LSB (most of them were 0). Now I use DMA mode ...
shesay stm32/stm8
430flash problem
After writing the address to 430, the power is turned off, and then the power is turned on again, a small part of the address will change. What's going on? ? ? ?...
775440788 Microcontroller MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1829  1396  554  1269  2056  37  29  12  26  42 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号