B22EV-JB datasheet, PDF - EEWORLD Datasheet

Datasheet> All Categories > Mechanical and electronic products> switch> B22EV-JB

B22EV-JB: DescriptionToggle Switch, DPDT, On-on, Maintained, 8 PCB Hole Cnt, Solder Terminal, Toggle Actuator, Through Hole-right Angle; CategoryMechanical and electronic products switch; File Size1MB，8 Pages; ManufacturerNKK Switches; Environmental Compliance

Download Datasheet Parametric View All

B22EV-JB Overview

Toggle Switch, DPDT, On-on, Maintained, 8 PCB Hole Cnt, Solder Terminal, Toggle Actuator, Through Hole-right Angle

B22EV-JB Parametric

Parameter Name	Attribute value
Is it Rohs certified?	conform to
Reach Compliance Code	not_compliant
ECCN code	EAR99
Actuator angle	26 deg
Executor completed	NICKEL
Actuator length	0.394 inch
Actuator material	BRASS
Actuator type	TOGGLE
Other features	CAP COLOR- WHITE
body width	8.7884 mm
body height	16.256 mm
Body length or diameter	8.7884 mm
Casing diameter	0.236 inch
Nozzle length	0.106 inch
Casing type	UNTHREADED
center contact material	PHOSPHOR BRONZE
Center contact plating	GOLD
Contact (DC) maximum rated power R load	0.4VA@28VDC
Contact function	ON-ON
Contact resistance	0.05 mΩ
contact time	BREAK-BEFORE-MAKE
Dielectric withstand voltage	500VAC V
Electrical life	50000 Cycle(s)
End contact material	COPPER ALLOY
End contact plating	GOLD
Insulation resistance	500000000 Ω
insulator material	GLASS FILLED POLYAMIDE
JESD-609 code	e4
Manufacturer's serial number	B
Installation features	THROUGH HOLE-RIGHT ANGLE
Maximum operating temperature	85 °C
Minimum operating temperature	-30 °C
PCB hole count	8
seal	EPOXY
surface mount	NO
Switch action	MAINTAINED
switch function	DPDT
Switch type	TOGGLE SWITCH
Terminal surface	Gold (Au)
Terminal length	0.122 inch
Terminal material	COPPER ALLOY
Termination type	SOLDER

Preview

Download Datasheet

View All

Series B

Toggles

Process Sealed Subminiature Antistatic Toggles

General

Specifications

Electrical Capacity (Resistive Load)

Logic Level:

0.4VA maximum @ 28V AC/DC maximum

(Applicable Range 0.1mA ~ 0.1A @ 20mV ~ 28V)

Note: Find additional explanation of operating range in Supplement section.

Pushbuttons

Rockers

Other Ratings

Programmable Illuminated PB

Contact Resistance:

Insulation Resistance:

Dielectric Strength:

Mechanical Life:

Electrical Life:

Nominal Operating Force:

Keylocks

Contact Timing:

Angle of Throw:

50 milliohms maximum

500 megohms minimum @ 500V DC

500V AC minimum for 1 minute minimum

100,000 operations minimum for On-None-On & On-Off-On

50,000 operations minimum for other circuits

50,000 operations minimum for locking lever models

50,000 operations minimum

Toggles A, A1, E & K with Long Paddle: 1.47N (momentary); 1.18N (maintained)

Toggles J & H & K with Short Paddle: 2.72N (momentary); 1.84N (maintained)

Toggle L: 0.59N

Nonshorting (break-before-make)

26°

Materials & Finishes

Rotaries

Toggle:

Bushing:

Gasket:

Case Housing:

Support Bracket:

Movable Contact:

Stationary Contacts:

Terminals:

Nickel plated brass

Carbon blended polyamide; nickel plated zinc alloy for locking levers & threaded bushing

Nitrile butadiene rubber

Glass fiber reinforced polyamide

Tin plated phosphor bronze

Phosphor bronze with gold plating

Copper alloy with gold plating

Tactiles

Slides

Environmental Data

Operating Temperature Range:

Humidity:

Vibration:

Shock:

–30°C through +85°C (–22°F through +185°F)

90 ~ 95% humidity for 96 hours @ 40°C (104°F)

10 ~ 55Hz with peak-to-peak amplitude of 1.5mm traversing the frequency range & returning

in 1 minute; 3 right angled directions for 2 hours

50G (490m/s

) acceleration (tested in 6 right angled directions, with 5 shocks in each direction)

Tilt

Touch

Installation

Mounting Torque:

.30 ~ .45Nm (2.65 ~ 3.98 lb

•

in) for A1 actuator with threaded bushing only

PCB Processing

Indicators

Soldering:

Cleaning:

Wave Soldering Recommended: See Profile A in Supplement section.

Manual Soldering: See Profile A in Supplement section.

Automated cleaning. See Cleaning specifications in Supplement section.

Accessories

Standards & Certifications

Flammability Standards:

Supplement

UL94V-0 available

The B Series toggles have not been tested for UL recognition or CSA certification.

These switches are designed for use in a low-voltage, low-current, logic-level circuit.

When used as intended in a logic-level circuit, the results do not produce hazardous energy.

A12

www.nkk.com

Recommended Resources

Simple 24-hour clock circuit diagram

Power supply example circuit diagram using SI9120

Small indoor induction cordless phone host

long timer

HA13001 power amplifier circuit

555 simple voltage controlled oscillator

Ask questions carefully, don't pass by, come in and take a look -: How to write the following program?Ask for advice[[i] This post was last edited by Yongxinsixiang on 2012-5-28 07:05[/i]]...; 用心思考 51mcu

Key Points of Porting μCOS-II to ARM Processor: ． Set up the processor and compiler related codes in OS_CPU.H /******************************************************************** * * Compiler related data types*************************************...; 呱呱 ARM Technology

Inventory of diodes and eight major circuit protection components: Circuit protection components have a wide range of applications. As long as there is electricity, there is a need to install circuit protection components, such as various household appliances, home a...; 鬼谷清泉 Analog electronics

[Qinheng RISC-V core CH582] 5-SPI drive OLED: [i=s]This post was last edited by manhuami2007 on 2022-3-13 20:20[/i]The SPI provided by CH582 supports mode 0 and mode 3, can be configured as 3-wire or 2-wire mode, supports master and slave modes, ...; manhuami2007 Domestic Chip Exchange

Happy Lantern Festival to everyone! What's the strangest filling of Yuanxiao you've ever eaten?: [font=微软雅黑][size=3][color=#ff0000][b]Today is the 15th day of the first lunar month, the Lantern Festival. I wish you all a happy holiday! [/b][/color][/size][/font][font=微软雅黑][size=3]Some people ask ...; eric_wang Talking

c/c++ determine whether the sd card space is sufficient: I am using Qt to write a graphical interface for a development board. I need to determine whether the SD card storage space is sufficient. Does anyone have any solution? Thanks...; lishi1991 Linux and Android

Shortcut: S0 S1 S2 S3 S4 S5 S6 S7 S8 S9 SA SB SC SD SE SF SG SH SI SJ SK SL SM SN SO SP SQ SR SS ST SU SV SW SX SY SZ T0 T1 T2 T3 T4 T5 T6 T7 T8 T9 TA TB TC TD TE TF TG TH TI TJ TK TL TM TN TO TP TQ TR TS TT TU TV TW TX TY TZ U0 U1 U2 U3 U4 U6 U7 U8 UA UB UC UD UE UF UG UH UI UJ UK UL UM UN UP UQ UR US UT UU UV UW UX UZ V0 V1 V2 V3 V4 V5 V6 V7 V8 V9 VA VB VC VD VE VF VG VH VI VJ VK VL VM VN VO VP VQ VR VS VT VU VV VW VX VY VZ W0 W1 W2 W3 W4 W5 W6 W7 W8 W9 WA WB WC WD WE WF WG WH WI WJ WK WL WM WN WO WP WR WS WT WU WV WW WY X0 X1 X2 X3 X4 X5 X7 X8 X9 XA XB XC XD XE XF XG XH XK XL XM XN XO XP XQ XR XS XT XU XV XW XX XY XZ Y0 Y1 Y2 Y4 Y5 Y6 Y9 YA YB YC YD YE YF YG YH YK YL YM YN YP YQ YR YS YT YX Z0 Z1 Z2 Z3 Z4 Z5 Z6 Z8 ZA ZB ZC ZD ZE ZF ZG ZH ZJ ZL ZM ZN ZP ZR ZS ZT ZU ZV ZW ZX ZY

Popular Components