EEWORLDEEWORLDEEWORLD

Part Number

Search

54122-414-62-2100

Description
Board Connector, 124 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle,
CategoryThe connector    The connector   
File Size107KB,1 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

54122-414-62-2100 Overview

Board Connector, 124 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle,

54122-414-62-2100 Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Reach Compliance Codecompliant
ECCN codeEAR99
body width0.19 inch
subject depth0.827 inch
body length6.2 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationSN ON NI
Contact completed and terminatedTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialTHERMOPLASTIC
JESD-609 codee0
Manufacturer's serial number54122
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Installation option 1LOCKING
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.54 mm
Plating thickness79u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.12 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts124
PDM: Rev:K
STATUS:
Released
Printed: Mar 10, 2011
.
How to sample the voltage and current at the AC end of the PFC circuit?
I use DSP to make a PFC circuit. What device should I use to sample the voltage and current of the input AC? Is the Hall sensor too large? If I use a resistor directly, the current will be negative. T...
hfutdsplab PCB Design
The reason why the pipe burns when it is connected
As shown in the figure, the power supply is dual 16. As soon as the TIP41 and TIP42 tubes are connected, they burn out after a while after power is turned on. When TIP41 and TIP42 are removed, the par...
量子阱 Analog electronics
ip
DHCP AUTOIP Static IPAfter DHCP fails, the system will use AUTOIP to configure the IP. I want it to use STATIC static IP after DHCP fails. Question 1: I want to use STATIC static IP after DHCP fails. ...
zhaoxuanttkl Embedded System
How to write a testbench
1. Setting incentives The input stimulus corresponding to the module under test is set to reg type, the output is set to wire type, and the bidirectional port inout needs to be processed during the te...
eeleader FPGA/CPLD
Detailed explanation of the connection technology between CF card and CPLD in ARM embedded system
With the continuous improvement of application requirements, many embedded systems require extended large-capacity storage to store data when applied. CF cards (Compact Flash Cards) are widely used in...
fish001 Microcontroller MCU
Linux embedded technology enthusiasts exchange group
Linux embedded technology enthusiasts exchange group 68158867 welcomes all enthusiasts to join! ! ! !...
stronghui Linux and Android

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2390  177  2559  1370  2788  49  4  52  28  57 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号