2200SGG5004A2MB datasheet, PDF

2200SGG5004A2MB: DescriptionStrain Guage Sensor, Gage, 0Psi Min, 500Psi Max, 0.15%, 0-10V, Cylindrical; CategoryThe sensor Sensor/transducer; File Size507KB，4 Pages; ManufacturerGems Sensors & Controls

Download Datasheet Parametric View All

2200SGG5004A2MB Overview

Strain Guage Sensor, Gage, 0Psi Min, 500Psi Max, 0.15%, 0-10V, Cylindrical

Parameter Name	Attribute value
Is it Rohs certified?	incompatible
Reach Compliance Code	unknow
Maximum accuracy(%)	0.15%
shell	STAINLESS STEEL
Nominal offset	0V
Maximum operating temperature	125 °C
Minimum operating temperature	-40 °C
Output range	0-10V
Output type	ANALOG VOLTAGE
Package Shape/Form	CYLINDRICAL
port type	7/16 MALE
Maximum pressure range	500 Psi
Minimum pressure range
Pressure sensing mode	GAGE
Sensor/Transducer Type	PRESSURE SENSOR,STRAIN GUAGE
Maximum supply voltage	35 V
Minimum supply voltage	1.5 V
Termination type	DIN 9.4MM W/MATE
Base Number Matches	1

Looking for partners, about arm 9200: Due to the shortened project schedule, I am looking for a partner. The general situation is as follows: the board has been made, it can be started normally, Linux can also run, and I have made some dr...; sen234 ARM Technology

【Book Collection】Demonstration Tutorial on Basic Engineering Test Technology: ...; wzt Test/Measurement

2410 or 2440 development board with WIFI module, there are: As the title says, I want to develop a small device based on WIFI, but I can't find a 2410 or 2440 development board with WIFI function. There are other ARM11 ones, but they are not suitable. I only n...; nishitamade Embedded System

PT6311.pdf: A brief introduction to the PT6311 chip is very good ....; rain RF/Wirelessly

The process of WEBENCH design + FPGA multi-power design under the guidance of WEBENCH (2): [i=s]This post was last edited by Diguapatch on 2014-8-18 18:21[/i] The webench online design software has a multi-power design solution specifically for FPGAs and microprocessors. The mainstream manu...; 地瓜patch Analogue and Mixed Signal

Asking for advice on the LT1248 chip problem in the PFC circuit: My PFC circuit uses LT1248 chip, output 500W, followed by a half-bridge circuit output 36V14A, the half-bridge is adjusted fine, but there is a noise on the PFC side after loading, the bigger the load...; gyf20022 Analog electronics

Shortcut: A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 AA AB AC AD AE AF AG AH AI AJ AK AL AM AN AO AP AQ AR AS AT AU AV AW AX AY AZ B0 B1 B2 B3 B4 B5 B6 B7 B8 B9 BA BB BC BD BE BF BG BH BI BJ BK BL BM BN BO BP BQ BR BS BT BU BV BW BX BY BZ C0 C1 C2 C3 C4 C5 C6 C7 C8 C9 CA CB CC CD CE CF CG CH CI CJ CK CL CM CN CO CP CQ CR CS CT CU CV CW CX CY CZ D0 D1 D2 D3 D4 D5 D6 D7 D8 D9 DA DB DC DD DE DF DG DH DI DJ DK DL DM DN DO DP DQ DR DS DT DU DV DW DX DZ

Popular Components