EEWORLDEEWORLDEEWORLD

Part Number

Search

3KT28/2CV3

Description
EDGE CONNECTOR,PCB MNT,RECEPT,56 CONTACTS,0.125 PITCH,WRAP POST TERMINAL,HOLE .112-.124
CategoryThe connector    The connector   
File Size420KB,4 Pages
ManufacturerCooper Industries
Download Datasheet Parametric View All

3KT28/2CV3 Overview

EDGE CONNECTOR,PCB MNT,RECEPT,56 CONTACTS,0.125 PITCH,WRAP POST TERMINAL,HOLE .112-.124

3KT28/2CV3 Parametric

Parameter NameAttribute value
Reach Compliance Codeunknown
ECCN codeEAR99
body width0.33 inch
subject depth0.437 inch
body length4.305 inch
Body/casing typeRECEPTACLE
Connector typeCARD EDGE CONNECTOR
Contact to complete cooperationAU ON NI
Contact materialCOPPER ALLOY
contact modeRECTANGULAR
Contact styleBELLOWED TYPE
Dielectric withstand voltage1500VDC V
maximum insertion force4.448 N
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialGLASS FILLED POLYESTER
MIL complianceYES
Manufacturer's serial numberCV
Plug contact pitch0.125 inch
Match contact row spacing0.145 inch
Installation option 1HOLE .112-.124
Installation option 2THREADED
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature105 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing3.683 mm
Plating thickness10u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityMIL-C-21097
Terminal length0.38 inch
Terminal pitch3.175 mm
Termination typeWIRE WRAP
Total number of contacts56
Evacuation force-minimum value.278 N
Circuit Analysis
What is the role of this transistor and voltage regulator here? Also, if the transistor on RB2 is disconnected, will the high level continue?The thing on the far right is a memory device with data in ...
nt06 Analog electronics
How does WinCE load the HID device after the system starts?
I wrote a HID class joystick driver. If I write the registry information into Loadclients first and then insert the joystick, the driver can work properly. The problem now is that since the WinCE plat...
cyu02 Embedded System
How to use the processor IO port to control the enable end of the power chip? I have fallen into an endless loop.
[size=3]As shown in the picture, I see that in general application manuals, the enable terminal is connected to the ground or the input source to enable it, but this way it cannot be controlled by a s...
flying~ Power technology
Rectification circuit
Single-phase half-wave rectifier circuit diagramWaveformSingle-phase full-wave rectifier circuit diagram and waveformWhy does the transformer of single-phase rectification need to be grounded in order...
eeboyok Analog electronics
Initialization of 8255
Use 8255 to detect the status of 8 external switches. When all 8 switches are disconnected, the system outputs a control signal; if more than one switch is closed, another control signal is output. Pl...
qqews2552 Embedded System
Real-time dynamic simulation of proteus and single-chip microcomputer
About :) :) Proteus and microcontroller real-time dynamic simulation...
781349304 MCU

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 581  2045  473  2332  11  12  42  10  47  1 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号