EEWORLDEEWORLDEEWORLD

Part Number

Search

D-SUB-205AJ15SGZBB122

Description
D Type Connector, 15 Contact(s), Female, 0.109 inch Pitch, Solder Terminal, #4-40, Plug
CategoryThe connector    The connector   
File Size124KB,1 Pages
ManufacturerPalPilot
Download Datasheet Parametric View All

D-SUB-205AJ15SGZBB122 Overview

D Type Connector, 15 Contact(s), Female, 0.109 inch Pitch, Solder Terminal, #4-40, Plug

D-SUB-205AJ15SGZBB122 Parametric

Parameter NameAttribute value
Reach Compliance Codecompliant
ECCN codeEAR99
Other featuresROHS COMPLIANT
body width0.492 inch
subject depth0.492 inch
body length1.543 inch
Body/casing typePLUG
Contact to complete cooperationAU ON NI
Contact completed and terminatedTIN OVER NICKEL
Contact point genderFEMALE
Contact materialCOPPER ALLOY
contact modeSTAGGERED
Contact resistance15 mΩ
Contact styleRND PIN-SKT
Dielectric withstand voltage1000VAC V
Insulation resistance3000000000 Ω
Insulator colorBLUE
insulator materialPOLYAMIDE
Manufacturer's serial number205
Plug contact pitch0.109 inch
Match contact row spacing0.112 inch
Installation option 1#4-40
Installation option 2RIVET
Installation methodRIGHT ANGLE
Installation typeBOARD
PCB row number2
Number of rows loaded2
Maximum operating temperature105 °C
Minimum operating temperature-55 °C
PCB contact patternSTAGGERED
PCB contact row spacing2.8448 mm
Plating thicknessFLASH inch
Rated current (signal)3 A
GuidelineUL
reliabilityCOMMERCIAL
Shell surfaceZINC
Shell materialSTEEL
Terminal length0.125 inch
Terminal pitch2.7686 mm
Termination typeSOLDER
Total number of contacts15
ROHM Sensor Evaluation Kit (2) Use of Sensor Shield and software platform construction
[i=s]This post was last edited by x1816 on 2017-2-18 18:29[/i] [font=黑体][size=6][b]Shield board introduction[/b][/size][/font] [font=微软雅黑][size=3]Shield board is the bridge connecting the sensor board...
x1816 Sensor
9B96 development board routine usage instructions
9B96 development board routine instructions, who can send a copy?...
wzp2007 Microcontroller MCU
Problems with using Guard Ring when wiring op amps
When I was looking at an op amp datasheet, the layout guideline said that using a guard ring around the input wire can greatly reduce leakage current. I didn't really understand what a guard ring is....
zpccx PCB Design
Buffered I/O Example Program
Now let's look at an example. The program first defines a structure called pirate, and then declares two variables of this type. The program initializes one of the variables and writes it to the disk ...
chenbingjy Linux and Android
Discussion on PCB layout for weak signal measurement
[table=98%,rgb(238, 238, 238)] [tr][td] For PCB layout (op amp, AD, DA, reference) of weak signal measurement (μV or even nV level), can the reference be laid on a separate layer (4-layer board)? Will...
zca123 PCB Design
BGA DIY manual soldering problem solving
[i=s] This post was last edited by Qingye Piaoling on 2015-4-21 11:07 [/i] After a long period of thinking and improvement of comprehensive ability. The difference in success rate between BGA manual s...
青叶漂零 DIY/Open Source Hardware

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 2770  738  1522  83  601  56  15  31  2  13 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号