EEWORLDEEWORLDEEWORLD

Part Number

Search

367-7D00-063

Description
Board Connector, 110 Contact(s), 11 Row(s), Male, Straight, Press Fit Terminal, Black Insulator
CategoryThe connector    The connector   
File Size1MB,4 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

367-7D00-063 Overview

Board Connector, 110 Contact(s), 11 Row(s), Male, Straight, Press Fit Terminal, Black Insulator

367-7D00-063 Parametric

Parameter NameAttribute value
Reach Compliance Codeunknown
ECCN codeEAR99
body width0.976 inch
subject depth0.638 inch
body length0.724 inch
Connector typeBOARD CONNECTOR
Contact to complete cooperationAU
Contact point genderMALE
Contact materialCOPPER ALLOY
contact modeRECTANGULAR
Dielectric withstand voltage1050VAC V
Durability250 Cycles
Insulation resistance1000000000 Ω
Insulator colorBLACK
insulator materialGLASS FILLED LIQUID CRYSTAL POLYMER
Manufacturer's serial number367
Match contact row spacing0.073 inch
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number22
Number of rows loaded11
Maximum operating temperature105 °C
Minimum operating temperature-40 °C
PCB contact patternSTAGGERED
PCB contact row spacing.9906 mm
Plating thickness20u inch
Rated current (signal)1 A
GuidelineUL
reliabilityCOMMERCIAL
Terminal length0.079 inch
Terminal pitch0.9906 mm
Termination typePRESS FIT
Total number of contacts110
V853 Replace the startup LOGO
# The overview mainly describes how to replace the startup LOGO of V853 # Environmental software: V853 Tina 5.0 SDK Hardware: Allwinner V853 development board # Specific steps First, let's take a look...
aleksib Domestic Chip Exchange
Dear big brothers, please help me
module flash_mod(clk,rst,LED_OUT); input clk; inout rst; outputLED_OUT; //----------------------// reg [19:0]cnt; reg led_out; parameter T50ms=20'd999_999; //-------------------------// //------------...
xander_wang FPGA/CPLD
The problem of the servo not rotating when the nodemcu esp8266 development board drives it
[i=s]This post was last edited by xiguabuda on 2022-3-11 22:59[/i]I'm new to this. I'm using a development board and MicroPython to drive the servo, but there's no response. Could you please help me f...
xiguabuda MicroPython Open Source section
Mentor Usage Problems
Dear experts, after installing Mentor DC7.9.2, when Capture Design calls the component library, it cannot be displayed, but the component library can be opened separately. Is there any problem with th...
随风飘啊 PCB Design
Ask about the interrupt response speed
Hello everyone, I have been busy with the WM project recently and have not been online for a long time. I encountered a problem today and I would like to ask you for help. I hope you can give me some ...
huzhiming Embedded System
LM2576 output current problem
Dear experts: I have a question. When I use LM2576S-5.0 as a voltage regulator, why is the output current not 3A, but only 50MA? Please advise! The circuit diagram is attached....
fy_1970 51mcu

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1324  321  359  1907  1102  27  7  8  39  23 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号