EEWORLDEEWORLDEEWORLD

Part Number

Search

54122-418-56-2350

Description
Board Connector, 112 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle,
CategoryThe connector    The connector   
File Size107KB,1 Pages
ManufacturerAmphenol
Websitehttp://www.amphenol.com/
Download Datasheet Parametric View All

54122-418-56-2350 Overview

Board Connector, 112 Contact(s), 2 Row(s), Male, Straight, 0.1 inch Pitch, Solder Terminal, Locking, Black Insulator, Receptacle,

54122-418-56-2350 Parametric

Parameter NameAttribute value
Is it Rohs certified?incompatible
Reach Compliance Codecompliant
ECCN codeEAR99
body width0.19 inch
subject depth0.925 inch
body length5.6 inch
Body/casing typeRECEPTACLE
Connector typeBOARD CONNECTOR
Contact to complete cooperationSN ON NI
Contact completed and terminatedTin/Lead (Sn/Pb) - with Nickel (Ni) barrier
Contact point genderMALE
Contact materialPHOSPHOR BRONZE
contact modeRECTANGULAR
Contact styleSQ PIN-SKT
Insulation resistance5000000000 Ω
Insulator colorBLACK
insulator materialTHERMOPLASTIC
JESD-609 codee0
Manufacturer's serial number54122
Plug contact pitch0.1 inch
Match contact row spacing0.1 inch
Installation option 1LOCKING
Installation methodSTRAIGHT
Installation typeBOARD
Number of connectorsONE
PCB row number2
Number of rows loaded2
Maximum operating temperature125 °C
Minimum operating temperature-65 °C
PCB contact patternRECTANGULAR
PCB contact row spacing2.54 mm
Plating thickness79u inch
Rated current (signal)3 A
GuidelineUL, CSA
reliabilityCOMMERCIAL
Terminal length0.12 inch
Terminal pitch2.54 mm
Termination typeSOLDER
Total number of contacts112
PDM: Rev:K
STATUS:
Released
Printed: Mar 10, 2011
.
For a 4-layer board, is it possible to lay ground on all 4 layers?
I have drawn a 4-layer board. Can I lay ground on all 4 layers? From the top layer to the bottom layer, they are Signal1, GND, Power, and Signal2 respectively, but the power layer has a thick power li...
小小金 PCB Design
Open a thread to talk about KW41Z and Thread
[size=3]First, let's talk briefly about the KW41Z chip itself. At a glance, there is nothing very attractive except that the memory is relatively large. Of course, this memory cannot be underestimated...
lyzhangxiang NXP MCU
In STM8, TIM2, 3, and 4 are turned on at the same time, and the first interrupt time is inaccurate
void TIM2_INIT(void){TIM2_PSCR = 2; /*2-division to get 1MHZ timer clock, timer plus 1 is 1us*/TIM2_ARRH = 0x27; /*50ms interrupt once*/TIM2_ARRL = 0x10;TIM2_IER = 0x01; /*Update interrupt enable*/TIM...
lint001 stm32/stm8
opt3001 light sensor problem help
Using 51 MCU to simulate I2C timing to control opt3001 light sensor, the data captured by logic analyzer shows that opt3001 does not feedback ACK to MCU. What is the most likely problem in this case? ...
Kileo 51mcu
About the selection of pull-up and pull-down resistors at A and B ends of 485 bus
[size=4]Question: About RS485[/size] [size=4]Use a resistor to pull up[/size] [size=4]B uses a resistor to pull down[/size] [size=4]A and B are connected by resistors, [/size] [size=4]What are the app...
Jacktang Analogue and Mixed Signal

EEWorld
subscription
account

EEWorld
service
account

Automotive
development
circle

Robot
development
community

Index Files: 1704  2576  2417  1126  1924  35  52  49  23  39 
Datasheet   0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z
Room 1530, 15th Floor, Building B, No. 18 Zhongguancun Street, Haidian District, Beijing Telephone: (010) 82350740 Postal Code: 100190
Copyright © 2005-2026 EEWORLD.com.cn, Inc. All rights reserved 京ICP证060456号 京ICP备10001474号-1 电信业务审批[2006]字第258号函 京公网安备 11010802033920号